Taito MT-8 - The info thread - Pic heavy

Post by **zak** » December 5th, 2017, 6:56 pm

SuperPang wrote:
zak wrote: MP!

Post by **NoAffinity** » December 5th, 2017, 7:47 pm

Very nice and clean adaptation. Love it!

Post by **moshpit** » February 5th, 2018, 10:51 am

Short followup on this: I just talked to akishop if they can use their close relationship with Taito to do some manual magic. You'll never know. I'll keep you guys posted. Maybe.

Post by **Wurstkopp** » February 5th, 2018, 11:03 am

Post by **geotrig** » February 5th, 2018, 12:10 pm

Post by **moshpit** » March 10th, 2018, 5:36 pm

Yo UK. You ready for some trash?

http://ibb.co/kdU6tS
http://ibb.co/bTWx07

Post by **Wurstkopp** » March 10th, 2018, 5:49 pm

Post by **geotrig** » March 10th, 2018, 6:46 pm

And Ireland

Post by **geotrig** » March 22nd, 2018, 1:35 pm

/me furiously reading every last wurstkopp post !

Post by **geotrig** » April 1st, 2018, 8:18 pm

Bloody bajillion parts..... No wonder they only made nine

Sick of switching sockets from metric to imperial and back again mostly apart now just need I dread putting it back together if ever I get that far

Post by **thomj** » April 1st, 2018, 8:53 pm

Needs pics

Post by **geotrig** » April 1st, 2018, 9:47 pm

I cant get into the room to take any !!

will try and get some up over the next few days.
Those Hungarians really butchered the cp areas

Post by **thomj** » April 1st, 2018, 10:24 pm

Is yours retrievable or will you get a replacement made?

Post by **geotrig** » April 1st, 2018, 10:55 pm

I think it's retrievable once you strip off all the screws it doesn't look any better somebodies magnolia paint is all over it

But the steel is thin so should be easyish sort ,my main concern is getting the cp surround area square again but hopefully looks doable.

I don't have one of the below mounting plates for mounting sticks and I think it takes the middle bolts of the cp? Only guessing as I don't have one so that's something that I'll have to worry about later.. Although there is always the "hungarish"

Wurstkopp wrote:

-

Post by **thomj** » April 1st, 2018, 11:10 pm

Post by **geotrig** » April 12th, 2018, 1:13 pm

Wurstkopp wrote: BTT: I have been waiting months for a new audio amp, since one of the machines had none and it finally has arrived last week. The other machine needed a new connector on the audio pcb which I coincidentally found last week in an old Grundig TV. Wifey + kid will be away this weekend so there's a good chance I will find some time to drive to the gameroom, build the stuff in and finish both MT-8 machines.
Well, apart from them goddamn bezels.

Do you have a picture of the audio amp ? not sure ive seen it

Post by **Wurstkopp** » April 12th, 2018, 2:38 pm

Will do some pics at the end of next week.

Post by **geotrig** » April 12th, 2018, 2:39 pm

Post by **geotrig** » May 8th, 2018, 11:41 am

slow progress but cheap progress !!

IMAG0430.jpg

Post by **Wurstkopp** » May 10th, 2018, 3:01 pm

Take your time, mate.

Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy

Re: Taito MT-8 - The info thread - Pic heavy