System 256 and Boardmaster Supergun

Everything Supergun related
Forum rules
ArcadeOtaku forum introduction & rules
Eddierang
Posts: 84
Joined: September 1st, 2008, 5:24 am
Location: Houston, TX USA

Re: System 256 and Boardmaster Supergun

Post by Eddierang » February 10th, 2019, 4:14 am

Looks like it’s something more serious than replacing the fuse😡. I replaced the 1A fuse on the 12V line, fan on the system 256 started working, and then it crapped out again, so I blew the fuse unfortunately. Something is shorting the 12V and I’m not sure what it is.

User avatar
grantspain
Tech Head
Posts: 4409
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: System 256 and Boardmaster Supergun

Post by grantspain » February 10th, 2019, 12:59 pm

i would imagine 1a 12v supply is too low, 4a is the normal on a jamma supply for 12v and 16a for 5v line
namco system boards are quite power hungry

Eddierang
Posts: 84
Joined: September 1st, 2008, 5:24 am
Location: Houston, TX USA

Re: System 256 and Boardmaster Supergun

Post by Eddierang » February 11th, 2019, 7:28 am

Ok, well if that’s the case I saw on YouTube, Nozomi7585’s YouTube channel that the system 256 worked on his boardmaster when putting in Capcom Fighting Jam. Did he mod his boardmaster with higher current fuses?

User avatar
grantspain
Tech Head
Posts: 4409
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: System 256 and Boardmaster Supergun

Post by grantspain » February 11th, 2019, 8:55 am

i have no idea on that but 1a for running sound, fan and rom drive seems awfully low

User avatar
penrhos
Panel Beater
Posts: 1465
Joined: September 11th, 2008, 12:08 pm
Location: Leicester - UK
eBay: ngpd002

Re: System 256 and Boardmaster Supergun

Post by penrhos » February 11th, 2019, 12:33 pm

He'd have a job - the standard PSU in a boardmaster is the same rating as the PANA - 7A on +5 and 1A on +12 & -5. I swapped mine out for a bigger PSU as I kept blowing fuses.
2 * Vewlix-F, 1 * Sega Rally 3, 1 * PacMan Ball 2P Pusher, TAB V-Pin, 1 * DinoKing (JAMMA Converted).

Eddierang
Posts: 84
Joined: September 1st, 2008, 5:24 am
Location: Houston, TX USA

Re: System 256 and Boardmaster Supergun

Post by Eddierang » February 11th, 2019, 12:47 pm

Penrhos, which PSU did you use on your boardmaster?

Eddierang
Posts: 84
Joined: September 1st, 2008, 5:24 am
Location: Houston, TX USA

Re: System 256 and Boardmaster Supergun

Post by Eddierang » February 13th, 2019, 10:02 pm

I don’t think my question got really answered, can I just swap out fuses for higher current fuses on each line or do I have to change power supply as well when I change the sizes of the fuses? Would like to not have to do any serious modding if I don’t have to.

Eddierang
Posts: 84
Joined: September 1st, 2008, 5:24 am
Location: Houston, TX USA

Re: System 256 and Boardmaster Supergun

Post by Eddierang » February 14th, 2019, 7:14 am

Update: put another 1A fuse on the 12V fuse box holder. Tested SSF2, got sound and fan on board running again. At this moment I dare not try running system 256 on that power supply. So as you guys suggested, sanwa power supply is underpowered for System 256. Now if I’m going run system 256 through the Namco I/O what are my options here? Could go the option of buying an external Sun power supply but I need to come up with the connector piece that connects the power to the wall, and use my spare Sega Jamma I/O for controls (might save me a headache for kickharness doing it that way. Or buy myself a Capcom I/O. What are good replacement internal power supplies to look at if I were to go that route?

User avatar
grantspain
Tech Head
Posts: 4409
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: System 256 and Boardmaster Supergun

Post by grantspain » February 14th, 2019, 11:23 am

what is the rating on the power supply of the 12v line?

User avatar
penrhos
Panel Beater
Posts: 1465
Joined: September 11th, 2008, 12:08 pm
Location: Leicester - UK
eBay: ngpd002

Re: System 256 and Boardmaster Supergun

Post by penrhos » February 14th, 2019, 11:47 am

The two I had, one had a Sanwa SWN-7F the other a CS-070 both are rated at:-

+5V @ 10A
+12V @ 1A
-5V @ 1A

Personally I'd use a small PC power supply with an ATX-Naomi power adapter to run the 246/256 as it'll be cheaper than a SUN PSU and 100V stepdown to run it. That way the BM is "Stock".

There is enough space to install a bigger PSU inside the BM but finding one that'll fit and where the +5V adjuster pot lines up with the hole in the back will be a problem - one I'm working on at the moment as my PSU was 100V only and the PSU I swapped to I can't adjust the +5V as the pot is in the wrong place.
2 * Vewlix-F, 1 * Sega Rally 3, 1 * PacMan Ball 2P Pusher, TAB V-Pin, 1 * DinoKing (JAMMA Converted).

Eddierang
Posts: 84
Joined: September 1st, 2008, 5:24 am
Location: Houston, TX USA

Re: System 256 and Boardmaster Supergun

Post by Eddierang » February 14th, 2019, 5:39 pm

I would like a have an ATX to Naomi power supply cable made for me if possible. Willing to pay for it.

Post Reply