Nanao MS-2930-S contrast improvement tips?

For monitor related issues
K405
Please Continue...
Posts: 14
Joined: December 15th, 2015, 2:12 pm
Location: The Netherlands

Nanao MS-2930-S contrast improvement tips?

Post by K405 » October 2nd, 2016, 10:32 am

I have a Nanao MS-2930-S in my Sega Blast City which has a darkened picture while the contrast pot is set to maximum level. Is there anything I can do to restore the contrast levels? Replace certain capacitors perhaps?
Last edited by K405 on October 2nd, 2016, 9:07 pm, edited 1 time in total.

User avatar
grantspain
Tech Head
Posts: 4437
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: Nanao MS-2930-S brightness improvement tips?

Post by grantspain » October 2nd, 2016, 11:07 am

change 10uf 250v cap on neck card

you have colour cut offs and a sub contrast on the main chassis
there is a screen volts pot on the flyback

Asure
Posts: 570
Joined: April 17th, 2013, 5:16 pm
Location: Netherlands
eBay: asure_nl

Re: Nanao MS-2930-S brightness improvement tips?

Post by Asure » October 2nd, 2016, 12:21 pm

If you have the dip switches on the remote board set to wrong (vga / dsub) and are using 15khz jamma, this will also happen..

Sw3 on the board: (right hand side)

http://www.gamestone.co.uk/gsrcade/arca ... top_tn.jpg

K405
Please Continue...
Posts: 14
Joined: December 15th, 2015, 2:12 pm
Location: The Netherlands

Re: Nanao MS-2930-S brightness improvement tips?

Post by K405 » October 2nd, 2016, 8:51 pm

grantspain wrote:change 10uf 250v cap on neck card

you have colour cut offs and a sub contrast on the main chassis
there is a screen volts pot on the flyback
Will do, thanks a lot for your time and reply.

K405
Please Continue...
Posts: 14
Joined: December 15th, 2015, 2:12 pm
Location: The Netherlands

Re: Nanao MS-2930-S contrast improvement tips?

Post by K405 » October 2nd, 2016, 9:04 pm

K405 wrote:
grantspain wrote:change 10uf 250v cap on neck card

you have colour cut offs and a sub contrast on the main chassis
there is a screen volts pot on the flyback
Will do, thanks a lot for your time and reply.
Actually I realize now I wrote brightness pot but I meant contrast pot! Sorry for being so daft :awe:
Does the 10uf cap on the neck board still apply in this case?

K405
Please Continue...
Posts: 14
Joined: December 15th, 2015, 2:12 pm
Location: The Netherlands

Re: Nanao MS-2930-S brightness improvement tips?

Post by K405 » October 2nd, 2016, 9:10 pm

Asure wrote:If you have the dip switches on the remote board set to wrong (vga / dsub) and are using 15khz jamma, this will also happen..

Sw3 on the board: (right hand side)

http://www.gamestone.co.uk/gsrcade/arca ... top_tn.jpg
Image


Yes, I have set to DIP 3 to off, thanks for the info.

User avatar
grantspain
Tech Head
Posts: 4437
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: Nanao MS-2930-S contrast improvement tips?

Post by grantspain » October 2nd, 2016, 9:40 pm

K405 wrote:
K405 wrote:
grantspain wrote:change 10uf 250v cap on neck card

you have colour cut offs and a sub contrast on the main chassis
there is a screen volts pot on the flyback
Will do, thanks a lot for your time and reply.
Actually I realize now I wrote brightness pot but I meant contrast pot! Sorry for being so daft :awe:
Does the 10uf cap on the neck board still apply in this case?
do you mean SUB contrast or contrast,have you located the cut off pots and yes the 10uf 250v cap is one of the most common nanao failures on virtually all their range of chassis

K405
Please Continue...
Posts: 14
Joined: December 15th, 2015, 2:12 pm
Location: The Netherlands

Re: Nanao MS-2930-S contrast improvement tips?

Post by K405 » October 4th, 2016, 6:50 pm

The contrast pot on the front is set to maximum and I have located the sub.contrast pot which I also set to maximum level which increased contrast slightly. Both are now set to the maximum level which gives an ok picture but it could do with a little bit more contrast.

Image

The RGB cut-off's are below the sub cont but they don't do any good for contrast.

Haven't located the 10uF capacitor yet. You can't see it from here can you?

Image

User avatar
grantspain
Tech Head
Posts: 4437
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: Nanao MS-2930-S contrast improvement tips?

Post by grantspain » October 4th, 2016, 10:08 pm

its the other side of the tube neck-its an extremely common fault

User avatar
Asayuki
Posts: 431
Joined: August 29th, 2015, 10:16 pm
Location: Remuria, Germany

Re: Nanao MS-2930-S contrast improvement tips?

Post by Asayuki » October 5th, 2016, 1:00 am

Cleaning the board a bit with a very soft brush will help you locate the capacitor.
My 15kHz cabinet Peplos will never power up, with any item, and I am quite proud of that.

K405
Please Continue...
Posts: 14
Joined: December 15th, 2015, 2:12 pm
Location: The Netherlands

Re: Nanao MS-2930-S contrast improvement tips?

Post by K405 » November 25th, 2016, 2:22 pm

Huge thank you grantspain!
Finally had time to replace that capacitor, lovely picture, great way to start the weekend. :D 8-)

Image

C332

Electrolytic capacitor Radial lead 5 mm 10 µF 250 V

Image

Frankee303
Please Continue...
Posts: 2
Joined: April 27th, 2018, 12:52 pm
Location: Germany
eBay: Brocken303
Initials: FWL

Re: Nanao MS-2930-S contrast improvement tips?

Post by Frankee303 » April 27th, 2018, 12:56 pm

Hi@all!

Same problem here!

Now I changed the Cap at the neckboard and the screen is a lil bit darker than before with the original cap.
Is there any trick to get more contrast?

Color cut offs and screen volts make the screen only wihite richt?
Or should I open the color cut offs and reduce the screen volts`?

Or can the new cap be broken too? :awe:

User avatar
yosai
280bpm's too slow
Posts: 3695
Joined: August 17th, 2008, 5:00 pm
Location: London
eBay: yosai

Re: Nanao MS-2930-S contrast improvement tips?

Post by yosai » April 27th, 2018, 2:03 pm

I'd definitely calibrate the monitor before you go any further.


https://wiki.arcadeotaku.com/w/How_to_C ... Brightness

Frankee303
Please Continue...
Posts: 2
Joined: April 27th, 2018, 12:52 pm
Location: Germany
eBay: Brocken303
Initials: FWL

Re: Nanao MS-2930-S contrast improvement tips?

Post by Frankee303 » April 27th, 2018, 3:46 pm

yosai wrote:I'd definitely calibrate the monitor before you go any further.


https://wiki.arcadeotaku.com/w/How_to_C ... Brightness
THX Bro I changed the settings and it´s fine now!

Just put brightness half open, color cut offs and then find the right voltage..

But it´s not the same overpowered **** to have the DSUB -75OHMs (with lowered contrast) - thats a color boost dafuq <3

fire10
Posts: 14
Joined: June 25th, 2015, 11:02 pm
Location: bognor regis

Re: Nanao MS-2930-S contrast improvement tips?

Post by fire10 » December 4th, 2019, 9:36 pm

Guys on the ms 2930 where is the adjustment for pincussion etc on the chassis please, does anyone have a pic. Many thanks in advance

User avatar
nem
Posts: 1526
Joined: August 17th, 2008, 6:59 pm
Location: Finland

Re: Nanao MS-2930-S contrast improvement tips?

Post by nem » December 5th, 2019, 10:06 am

All the pots are on one side of the chassis. There's two pots for pincushion adjustment, S.P.C and S.P.C 15.

http://tof.canardpc.com/view/dd0bace2-b ... 45c50f.jpg

In the above pic, S.P.C 15 is the third pot from the right. There's also S.P.C to the right of the circled pot. Both have an effect for all resolutions, S.P.C 15 more pronounced for standard resolution.

User avatar
radiantsvgun
Posts: 136
Joined: January 13th, 2009, 9:20 pm
Location: Georgia, USA
eBay: Radiantsvgun
Initials: RIC

Re: Nanao MS-2930-S contrast improvement tips?

Post by radiantsvgun » December 5th, 2019, 10:54 am

nem wrote:
December 5th, 2019, 10:06 am
All the pots are on one side of the chassis. There's two pots for pincushion adjustment, S.P.C and S.P.C 15.

http://tof.canardpc.com/view/dd0bace2-b ... 45c50f.jpg

In the above pic, S.P.C 15 is the third pot from the right. There's also S.P.C to the right of the circled pot. Both have an effect for all resolutions, S.P.C 15 more pronounced for standard resolution.
Thanks Nem, I'm having a similar problem and I cant see which pot is which in the windy. Much appreciated.

fire10
Posts: 14
Joined: June 25th, 2015, 11:02 pm
Location: bognor regis

Re: Nanao MS-2930-S contrast improvement tips?

Post by fire10 » December 5th, 2019, 8:45 pm

Amazing info thankyou mate, do I have to take the monitor out to adjust or is it possible to leave it in whilst adjusting. What do you use to adjust, thanks again buddy. One last question, is there any way to up the colour intensity, I've tried contrast and brightness, my pictures colour is really good but I'd like to be able to adjust it a bit. Thanks for your time once again

User avatar
nem
Posts: 1526
Joined: August 17th, 2008, 6:59 pm
Location: Finland

Re: Nanao MS-2930-S contrast improvement tips?

Post by nem » December 6th, 2019, 2:12 pm

fire10 wrote:
December 5th, 2019, 8:45 MP
Amazing info thankyou mate, do I have to take the monitor out to adjust or is it possible to leave it in whilst adjusting.

I would take it out, but it can be done with the monitor inside the cab. It's just not very fun.

What do you use to adjust, thanks again buddy.

Well, a trimmer tool with a plastic end is what's preferred, however, any small screwdriver will do.

One last question, is there any way to up the colour intensity, I've tried contrast and brightness, my pictures colour is really good but I'd like to be able to adjust it a bit.

You need to adjust color gains on the remote. Unfortunately, due to some idiotic reason they're behind the mounting plate on the Blast :problem: You need to remove the monitor to remove the remote.

fire10
Posts: 14
Joined: June 25th, 2015, 11:02 pm
Location: bognor regis

Re: Nanao MS-2930-S contrast improvement tips?

Post by fire10 » December 6th, 2019, 11:12 pm

Thankyou very much mate. Is there a user manual available for the ms2930. Also on the ms2930 how do I access the convergence grid test please. Many thanks once again

Post Reply