Raiden DX + superguns
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Raiden DX + superguns
Hi all - I read these Seibu boards sometimes don’t play nice with superguns. My dx board doesn’t work (works fine in NAC). I think the voltage demand is maybe higher though, which I can control a bit, will try again later. Just seeing if anyone has experience with these. Supergun fine with other boards.
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Raiden DX + superguns
Does Raiden DX really pull that much juice? Test with a multimeter.
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Thanks will do. Have a little voltage meter on the jamma edge in the NAC I think it showed 5.4v when dx was plugged in will check later.
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Raiden DX + superguns
Yeah, that's too high. Double check with multimeter. You want between 4.95-5.05V on the jamma edge, no more, no less.
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Good shout will check in the NAC at the jamma and dial down.
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Dialed in the 5v on the NAC, dx runs fine as far as I can see, so no need for more voltage on my board. Supergun still no joy maybe a display related thing. Appreciate the heads up NAC voltage was too high in general.
You do not have the required permissions to view the files attached to this post.
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Raiden DX + superguns
Does it play blind on the supergun? You can hear sounds when you start a game?
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Hi - no, no sound. It’s a cbox into retro rink 2x scart to flex scan 4:3 lcd. I remember turtles not working well either but connected through unlike this. Might have to get on and rotate the nac!
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Raiden DX + superguns
It's not a display issue then. The game doesn't care if there's no monitor connected, it will still run normally.
Did you measure voltages with the supergun?
Did you measure voltages with the supergun?
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Supergun does have a little voltage meter wired in that the jamma edge so was defo supplying 5v (according to that) might check again later with the multimeter too.
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Ok so does have sound..was being thick cos my monitor doesn’t have a speaker thought I’d checked the audio but
Hadn’t properly. So yes sound out, no pic. Voltage on jamma edge and on chips running fine just below 5v
Hadn’t properly. So yes sound out, no pic. Voltage on jamma edge and on chips running fine just below 5v
- cools
- Armed Police Buttrider
- Posts: 13459
- Joined: August 17th, 2008, 4:49 pm
- Location: Wales, United Kingdom
- eBay: hordarian
- Initials: CLS
Re: Raiden DX + superguns
Raiden DX runs at 55Hz, try different monitors.
Unlikely the RetroTink is the problem.
Unlikely the RetroTink is the problem.
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Ah ok. Thanks
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Ok think I ran out of monitors (which isn’t many to be fair). Have raiden fighters too same thing. Maybe it’s cab only until I can sort something else- shame as the eizo 4:3 monitor is decent.
-
- Posts: 57
- Joined: March 30th, 2021, 9:41 pm
- Location: United Kingdom
- eBay: ebay.co.uk/usr/mattcmonfeet
- Initials: TLS
Re: Raiden DX + superguns
Read a bit more on this with Seibu boards, tho in most cases people getting it sorted with a crt. This is into a eizo flexscan 4:3 2133 monitor which is decent (for lcd), rotates etc.Not sure if there is any path to getting it working using something external, but defo not 54/5 hertz according to the manual.
You do not have the required permissions to view the files attached to this post.
- dingsbums
- The bead-o empire
- Posts: 238
- Joined: June 26th, 2009, 10:38 am
- Location: Germany
Re: Raiden DX + superguns
All the Raiden PCBs (Raiden 1,2,DX, all three Raiden Fighters games & Viper Phase Vol.1) run at vertical sync rates between 54-56 khz. Its far off from the 60hz standard. LCDs nearly never support sync rates like that and even a lot of home use CRTs dont support it.