I just got my first ever arcade cabinet NAC and Im trying to rotate monitor to play shmups but afraid i cut wires or break something.
i appreciate ur advices.
i put images from front control panel and the back door of monitor.
what i need to remove?
do i need to remove the remote at control panel (the green board that controls brightness and contrast).
Noob trying to rotate NAC monitor first time
- Ali710
- Posts: 109
- Joined: April 29th, 2019, 9:53 am
- Location: Bahrain
- eBay: loyalforthegame9
- Initials: ALI
Noob trying to rotate NAC monitor first time
You do not have the required permissions to view the files attached to this post.
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Noob trying to rotate NAC monitor first time
Yeah, you need to disconnect the cable for the remote. There's not a whole lot of slack. The remote end is probably easier. Then there's the 15-pin connector at the back. That's it for connectors.
For panels, remove the back plate behind the marquee light. Then remove the monitor bezel.
Then undo the four bolts at the corners of the frame.
And that's it. The monitor can be then pulled out.
For panels, remove the back plate behind the marquee light. Then remove the monitor bezel.
Then undo the four bolts at the corners of the frame.
And that's it. The monitor can be then pulled out.
- Chempop
- Please Continue...
- Posts: 1046
- Joined: May 13th, 2011, 6:13 pm
- Location: North East USA
- eBay: Weegzon
- Initials: GLX
Re: Noob trying to rotate NAC monitor first time
Here is a video I found after making this makeshift guide, definitely worth a watch...
This will start you off, it is recommended to have a friend present your first time:
Unscrew:
You DO NOT need to unplug the remote board here, but if you can't reach it on the chassis via the back entry panel, is an option for you.
Unplug:
Beware:
Then the fun part. I lay cab on the back, unscrew the last 4 big bolts that hold the monitor in place, lift and rotate clockwise (but if you are hulk is not necessary). Put it back together
This will start you off, it is recommended to have a friend present your first time:
Unscrew:
You DO NOT need to unplug the remote board here, but if you can't reach it on the chassis via the back entry panel, is an option for you.
Unplug:
Beware:
Then the fun part. I lay cab on the back, unscrew the last 4 big bolts that hold the monitor in place, lift and rotate clockwise (but if you are hulk is not necessary). Put it back together
- Chempop
- Please Continue...
- Posts: 1046
- Joined: May 13th, 2011, 6:13 pm
- Location: North East USA
- eBay: Weegzon
- Initials: GLX
Re: Noob trying to rotate NAC monitor first time
I forgot one thing, at 9min:30sec in the youtube video, he rotates the monitor "frame" (black part around monitor". Many screws and quite annoying... this is one thing i like about blast city, it just pops in/out in 10 seconds.
Good luck, let us know how it goes.
Good luck, let us know how it goes.
- Eddhorse
- Posts: 113
- Joined: November 13th, 2015, 7:06 pm
- Location: Dublin, Ireland
- eBay: Eddlowry
- Initials: EDL
Re: Noob trying to rotate NAC monitor first time
Best of luck and do the cabinet a favour and give it a good clean
- dingsbums
- The bead-o empire
- Posts: 238
- Joined: June 26th, 2009, 10:38 am
- Location: Germany
Re: Noob trying to rotate NAC monitor first time
@chempop
Thats my very old & outdated rotate video .
Here is a better one exactly for the New Astro City (not mine)
Thats my very old & outdated rotate video .
Here is a better one exactly for the New Astro City (not mine)
- cthulhu
- Posts: 251
- Joined: October 31st, 2008, 9:10 pm
- Location: The Netherlands
- eBay: cthulhu_nl
- Initials: RIP
Re: Noob trying to rotate NAC monitor first time
I simply bought a second NAC...
-
- Posts: 100
- Joined: September 29th, 2013, 5:09 pm
- Location: