Tosh A68KJU96X Nanao MS8 not working - technical help needed
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Tosh A68KJU96X Nanao MS8 -> MS9 swap
Looks like everything is connected as it should.
Did you have a multimeter?
Did you have a multimeter?
- Benimaru
- Please Continue...
- Posts: 51
- Joined: October 12th, 2018, 8:23 pm
- Location: Germany
- eBay: extension55
- Initials: PDG
Re: Tosh A68KJU96X Nanao MS8 -> MS9 swap
The never ending story continues...
I've tried two different MS9's with the matching adapter cables. Absolutely nothing. No signs of life.
Then I've tried again the old, probably faulty, Sanwa chassis. I've received nothing but a white horizontal line this time. Not even a flickering picture anymore.
I've received a MS8 chassis today and attached everything to the tube, no adapters needed. The result however is the same as with the Sanwa: only a horizontal line...
I'm really getting desperate by now, as I don't have any clue what I could do anymore.
Does anyone of you experienced guys here have any idea what I could check next?
I've tried two different MS9's with the matching adapter cables. Absolutely nothing. No signs of life.
Then I've tried again the old, probably faulty, Sanwa chassis. I've received nothing but a white horizontal line this time. Not even a flickering picture anymore.
I've received a MS8 chassis today and attached everything to the tube, no adapters needed. The result however is the same as with the Sanwa: only a horizontal line...
I'm really getting desperate by now, as I don't have any clue what I could do anymore.
Does anyone of you experienced guys here have any idea what I could check next?
- grantspain
- Tech Head
- Posts: 4824
- Joined: August 17th, 2008, 4:23 pm
- Location: down south
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
read the vertical yoke winding impedance
- Benimaru
- Please Continue...
- Posts: 51
- Joined: October 12th, 2018, 8:23 pm
- Location: Germany
- eBay: extension55
- Initials: PDG
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
Just measured the yoke:
Yellow & Green: 5,7 Ohms
Red & Blue: 0,6 Ohms
Here's a picture of the shown line:
If I adjust the remote potis, the chassis shuts down the high voltage.
Yellow & Green: 5,7 Ohms
Red & Blue: 0,6 Ohms
Here's a picture of the shown line:
If I adjust the remote potis, the chassis shuts down the high voltage.
- grantspain
- Tech Head
- Posts: 4824
- Joined: August 17th, 2008, 4:23 pm
- Location: down south
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
unless you have loads of faulty chassis with the exact same fault then i would say there is an issue in the vertical winding of the yoke
- Benimaru
- Please Continue...
- Posts: 51
- Joined: October 12th, 2018, 8:23 pm
- Location: Germany
- eBay: extension55
- Initials: PDG
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
That doesn't sound good...
Would you say the monitor can be repaired?
Are the measured Ohms in a "regular" range?
Would you say the monitor can be repaired?
Are the measured Ohms in a "regular" range?
Last edited by Benimaru on October 9th, 2019, 12:19 pm, edited 1 time in total.
- grantspain
- Tech Head
- Posts: 4824
- Joined: August 17th, 2008, 4:23 pm
- Location: down south
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
you need to prove the issue before doing that, in other words you either need to test the chassis on a different tube or try a different yoke
- Benimaru
- Please Continue...
- Posts: 51
- Joined: October 12th, 2018, 8:23 pm
- Location: Germany
- eBay: extension55
- Initials: PDG
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
Here we go again...
Thanks to yosai, I was able to source down a Nanao compatible yoke pretty quickly.
Unfortunately the failure image stays pretty much the same:
It's really no fun anymore, 2 chassis, 2 yokes, 2 times the same failure?! Oh and of course I've cross checked the PSU. Same failure with a confirmed working one from another cab.
How's that even possible? Any further ideas? grantspain? nem? Have you ever had something simillar in the past?
Thanks to yosai, I was able to source down a Nanao compatible yoke pretty quickly.
Unfortunately the failure image stays pretty much the same:
It's really no fun anymore, 2 chassis, 2 yokes, 2 times the same failure?! Oh and of course I've cross checked the PSU. Same failure with a confirmed working one from another cab.
How's that even possible? Any further ideas? grantspain? nem? Have you ever had something simillar in the past?
- grantspain
- Tech Head
- Posts: 4824
- Joined: August 17th, 2008, 4:23 pm
- Location: down south
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
so you put a working chassis onto that tube and you still get vertical collapse- do you also swap the remote board?
- yosai
- Windy City
- Posts: 4061
- Joined: August 17th, 2008, 5:00 pm
- Location: London
- eBay: yosai
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
I'd check the remote board connections and the cable itself. It may be that the ribbon cable has been damaged.
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
I'm pretty sure you still have some deflection even if you have the remote unplugged.
Worth a look in any case.
Worth a look in any case.
- Benimaru
- Please Continue...
- Posts: 51
- Joined: October 12th, 2018, 8:23 pm
- Location: Germany
- eBay: extension55
- Initials: PDG
Re: Tosh A68KJU96X Nanao MS8 not working - technical help needed
I will receive another MS8 with remote in 1-2 weeks.
My technical knowledge is far from being a professional, but if it won't be either of the already swapped parts (chassis, yoke and soon remote board), what's left?
My technical knowledge is far from being a professional, but if it won't be either of the already swapped parts (chassis, yoke and soon remote board), what's left?
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland