Monster Land English : from Encryption to Decryption...

Coin-operated games and arcades.
Post Reply
Grish
Please Continue...
Posts: 14
Joined: October 8th, 2014, 1:29 am
Location:

Re: Monster Land English : from Encryption to Decryption...

Post by Grish »

Hi Guys,

I finally got around to burning my eproms with this legendary mpatou romset! Game runs perfectly apart from one issue;

I have an issue with my old bootleg board, it seems red has stopped working, I'm hoping someone can help a poor noob like me for any leads into where to look/replace etc.

Here's some pics of my issue and the board.
wbml_no_red - Copy.jpg
wbml_no_red_2 - Copy.jpg
IMG_20190323_103222_resized - Copy.jpg

Cheers,
Grish
You do not have the required permissions to view the files attached to this post.
User avatar
mpatou
Please Continue...
Posts: 67
Joined: November 19th, 2013, 9:37 am
Location: Brest (France)
eBay: mpatard1

Re: Monster Land English : from Encryption to Decryption...

Post by mpatou »

Hi

First thing you should do is cleaning the edge connector on the PCB : I personnaly use a cuetip with 90° alcohol, a friend o'mine use a rubber eraser, if you have an electric contact cleaner like KF, is great.

Then, I would check your adapter to see if the Red wire is still connected.

Please, do those checks then post here if it has worked or not.
Image
Grish
Please Continue...
Posts: 14
Joined: October 8th, 2014, 1:29 am
Location:

Re: Monster Land English : from Encryption to Decryption...

Post by Grish »

Thanks mate,

I did clean the edge connector and test the harness/adapter OK.

Unfortunately I've made the situation a lot worse by attempting to replace one of the 74ls174 chips (local elec store only had 74ls174n but based on data sheets I couldn't distinguish between them?)

I managed to break at least one trace and tried fixing that with a little hack wire, but now I'm getting repeated GFX (top third section of screen is repeated in lower third) :oops:

Plus still no red :cry:
User avatar
mpatou
Please Continue...
Posts: 67
Joined: November 19th, 2013, 9:37 am
Location: Brest (France)
eBay: mpatard1

Re: Monster Land English : from Encryption to Decryption...

Post by mpatou »

Why did you remove this 74ls174? Don't worry about the N at the end of 74ls174N
Image
Grish
Please Continue...
Posts: 14
Joined: October 8th, 2014, 1:29 am
Location:

Re: Monster Land English : from Encryption to Decryption...

Post by Grish »

I traced the red line to it from the edge connector, it was as far as I got, then I also read somewhere that someone else replaced a 174 and/or 175 to fix similar issues.

Unfortunately I didn't realise I could have tested using piggy back method, but you live and you learn right?
User avatar
mpatou
Please Continue...
Posts: 67
Joined: November 19th, 2013, 9:37 am
Location: Brest (France)
eBay: mpatard1

Re: Monster Land English : from Encryption to Decryption...

Post by mpatou »

Now you can try piggy packing to see if the new 74ls174 hasn't been damaged during installation.
Image
User avatar
keropi
Please Continue...
Posts: 294
Joined: January 14th, 2016, 6:04 pm
Location: Greece
eBay: sainshov

Re: Monster Land English : from Encryption to Decryption...

Post by keropi »

mpatou, any idea what could trigger glitches like that on an original board?

for example:

starting with the sword before talking to the 1st guy:

Image

random game overs:

Image

Image

glitches but game does not freeze

Image

Image

Image

Image

Image

roms checked (also burned 70ns eeproms , did not help) , sprite rams reversed back to originals, psu powering the game is a meanwell with more than enough amps . I also noticed that if you do not feed the game 5.10+ volts then the music plays a tad faster - small change in speed but I can notice. You could leave it demo for hours and it would be fine, then it started doing this before the knight fight on level 4 , then it started doing it at the town, then it creeped on 1st level too...

Board is nice and clean, no bad soldering or weirdnes: https://i.imgur.com/AqiSkD2.jpg
for reference this is the back side of the sockets I installed for the 6x sprite ram ICs: https://i.imgur.com/bM2wDc2.jpg

any idea what to look? thanks! :)
User avatar
mpatou
Please Continue...
Posts: 67
Joined: November 19th, 2013, 9:37 am
Location: Brest (France)
eBay: mpatard1

Re: Monster Land English : from Encryption to Decryption...

Post by mpatou »

Sprites look nice. As it's not only a display issue, I'd take a look around main CPU circuit (main CPU itself or associated ram IC).
Image
User avatar
keropi
Please Continue...
Posts: 294
Joined: January 14th, 2016, 6:04 pm
Location: Greece
eBay: sainshov

Re: Monster Land English : from Encryption to Decryption...

Post by keropi »

thanks for the input mpatou! appreciate it!!
yes it looks like a cpu work ram issue?
do you have any idea which ram is that on the board? is it the 2x SONY srams at M1 and N1 ? or the K5 one?
User avatar
mpatou
Please Continue...
Posts: 67
Joined: November 19th, 2013, 9:37 am
Location: Brest (France)
eBay: mpatard1

Re: Monster Land English : from Encryption to Decryption...

Post by mpatou »

The main CPU (z80 @ ic55)could be faulty too. Try to replace it.
Main CPU ram is ic93, next to main CPU romchips. It's not necessary the chip itself that is faulty, could be many things around it (LS244, LS374 etc...).
It's not easy to find what is wrong.
Image
User avatar
keropi
Please Continue...
Posts: 294
Joined: January 14th, 2016, 6:04 pm
Location: Greece
eBay: sainshov

Re: Monster Land English : from Encryption to Decryption...

Post by keropi »

Thanks again for the info!
Yes many many things could be wrong, a starting point helps!
I'll report back when the culprit is found
Grish
Please Continue...
Posts: 14
Joined: October 8th, 2014, 1:29 am
Location:

Re: Monster Land English : from Encryption to Decryption...

Post by Grish »

Hi Mpatou and all,

Quick update:

Red is now working! So the original problem I had is now fixed. It was a dodgy resistor meant to be 100ohms, but was reading 1Megohms! - Swapped it out and bingo back came red!

However, the other problem that I somehow managed to introduce while stupidly replacing the 74174 chip is still there (I tried piggy back with new 174 and nothing changed), the top quarter or third of screen repeats itself in lower part of the main game play window, the "border" appears fine! The pics say 1000 words anyway...

I know it's nothing to do with the PROMS and I'm now suspecting RAM, take a look at pics and if anyone has any clues please chime in!!!!!
1_red_get.jpg
wtf2.jpg
wtf.jpg
You do not have the required permissions to view the files attached to this post.
Grish
Please Continue...
Posts: 14
Joined: October 8th, 2014, 1:29 am
Location:

Re: Monster Land English : from Encryption to Decryption...

Post by Grish »

Cont...

This next part is VERY interesting, the problem doesn't show up on the credit screen if you credit up BEFORE the game demo runs....:
credit_screen_before_demo.jpg
After game demo has ran:
credit_screen_after_demo.jpg
You do not have the required permissions to view the files attached to this post.
User avatar
keropi
Please Continue...
Posts: 294
Joined: January 14th, 2016, 6:04 pm
Location: Greece
eBay: sainshov

Re: Monster Land English : from Encryption to Decryption...

Post by keropi »

can anyone with an original board tell me what value is the resistor in this pic? ?(or get a good one so I can see the colors) , it's the patch resistor above IC57
Thanks!!! :awe: :awe:

Image
User avatar
mpatou
Please Continue...
Posts: 67
Joined: November 19th, 2013, 9:37 am
Location: Brest (France)
eBay: mpatard1

Re: Monster Land English : from Encryption to Decryption...

Post by mpatou »

Hello

I think it doesn't matter, it's here just to provide 1 as logic value while not creating a short-circuit.
If you need to replace it, put something like 2Kohm or 4Kohm.
Image
User avatar
keropi
Please Continue...
Posts: 294
Joined: January 14th, 2016, 6:04 pm
Location: Greece
eBay: sainshov

Re: Monster Land English : from Encryption to Decryption...

Post by keropi »

^ thanks mpatou! :D
User avatar
keropi
Please Continue...
Posts: 294
Joined: January 14th, 2016, 6:04 pm
Location: Greece
eBay: sainshov

Re: Monster Land English : from Encryption to Decryption...

Post by keropi »

ok back with another question.... anyone knows what these jumpers on the System2 boards do?

Image

Image

more importantly, what are the correct settings for Monster Land?
I know there are various System 2 versions, I have 171-5303-01 (original choplifter) and 171-5305 (no idea if this was an original wboy2 or some other game)
thanks!!!
sknipas
Please Continue...
Posts: 2
Joined: September 2nd, 2019, 8:40 pm
Location: greece
eBay: karalazos
Initials: skn

Re: Monster Land English : from Encryption to Decryption...

Post by sknipas »

mpatou wrote: January 9th, 2019, 12:58 pm You've got a private message ;)
Can you send me the order of rom files to burn to eproms. I have a bootleg board also.
User avatar
keropi
Please Continue...
Posts: 294
Joined: January 14th, 2016, 6:04 pm
Location: Greece
eBay: sainshov

Re: Monster Land English : from Encryption to Decryption...

Post by keropi »

I forgot to report back, solved the issue months ago... It was the main Z80 - replaced it and all is fine again
User avatar
k1ngarth3r
Posts: 377
Joined: August 5th, 2011, 4:09 pm
Location: Derbyshire
eBay: t-0-m-t-0-m
Initials: Tom
Contact:

Re: Monster Land English : from Encryption to Decryption...

Post by k1ngarth3r »

Just out of Interest, I have a ChopLifter System 2 board, Is it just a case of downloading the decrypted ROMs and burning to get it converted?
Post Reply