Minicute art in the wiki
-
- Posts: 674
- Joined: February 18th, 2015, 12:03 am
- Location: Metro City
- eBay: jaime5171
Minicute art in the wiki
I;m trying to silk print the mini cute art in the wiki, but apparently I need vector files. The art in the wiki are pdfs. Does anyone know who uploaded them or has the vector files? Thanks!
- cools
- Armed Police Buttrider
- Posts: 13459
- Joined: August 17th, 2008, 4:49 pm
- Location: Wales, United Kingdom
- eBay: hordarian
- Initials: CLS
Re: Minicute art in the wiki
The speaker part is a bitmap PDF, the other two are vector PDFs
-
- Posts: 674
- Joined: February 18th, 2015, 12:03 am
- Location: Metro City
- eBay: jaime5171
Re: Minicute art in the wiki
Thanks, I'm not very handy with AI, I was just told that I needed vector files to silkprint so I just rasterised it and cut the holes, hope it turns out OK. Wiht bitmap, they told me it couldn't be done.cools wrote: The speaker part is a bitmap PDF, the other two are vector PDFs
- cools
- Armed Police Buttrider
- Posts: 13459
- Joined: August 17th, 2008, 4:49 pm
- Location: Wales, United Kingdom
- eBay: hordarian
- Initials: CLS
Re: Minicute art in the wiki
Raster = bitmap.
-
- Posts: 674
- Joined: February 18th, 2015, 12:03 am
- Location: Metro City
- eBay: jaime5171
Re: Minicute art in the wiki
Ok, then I vectorised it...cools wrote:Raster = bitmap.
-
- Posts: 674
- Joined: February 18th, 2015, 12:03 am
- Location: Metro City
- eBay: jaime5171
Re: Minicute art in the wiki
Well I finally got my Cute arts printed, not bad but I have a problem.
The speaker surrounding didn't have the holes in the wiki, so I decided to draw them cause I had no idea how to do perfect circles once printed. Well, I missed the size, luckily they are a tad small (too big would have been complete f***k up), so I am back to square one. How do I cut perfect circles into the sticker. Any ideas? I can't use the cab as a template cause it would ruin the paint...
Here is the art, silk printed:
This are the holes that need to be widen a little bit, like a cm.
The speaker surrounding didn't have the holes in the wiki, so I decided to draw them cause I had no idea how to do perfect circles once printed. Well, I missed the size, luckily they are a tad small (too big would have been complete f***k up), so I am back to square one. How do I cut perfect circles into the sticker. Any ideas? I can't use the cab as a template cause it would ruin the paint...
Here is the art, silk printed:
This are the holes that need to be widen a little bit, like a cm.
- orio1
- Posts: 125
- Joined: October 31st, 2013, 9:45 pm
- Location: Melbourne Australia
- eBay: e.bay
- Initials: OEO
- cools
- Armed Police Buttrider
- Posts: 13459
- Joined: August 17th, 2008, 4:49 pm
- Location: Wales, United Kingdom
- eBay: hordarian
- Initials: CLS
Re: Minicute art in the wiki
I'd find something the same size to use as a template, or get some metal water/laser cut.
- PrincessPrinPrin
- Posts: 577
- Joined: April 7th, 2011, 4:00 pm
- Location: Pordenone, Italy
- eBay: *mkl*
- Initials: MKL
Re: Minicute art in the wiki
https://www.amazon.co.uk/Rolson-62949-C ... B001MJ0BJIzumbito wrote:I had no idea how to do perfect circles once printed.