Convergence (Wei Ya Chassis/Samung Tube)
-
- Posts: 124
- Joined: February 18th, 2012, 7:54 pm
- Location:
Convergence (Wei Ya Chassis/Samung Tube)
So I've adjusted the yoke to get the picture lined up better. I've adjusted the rings, I've tried convergence strips.
Short version-the rest of the screen is as good as I can get. The lower portion (lower 10%) the red convergence is off. Is there something I'm missing or is this as good as it'll get?
Thanks!
Short version-the rest of the screen is as good as I can get. The lower portion (lower 10%) the red convergence is off. Is there something I'm missing or is this as good as it'll get?
Thanks!
You do not have the required permissions to view the files attached to this post.
- Rossyra
- Supermod
- Posts: 7902
- Joined: February 12th, 2009, 1:24 am
- Location: UK
Re: Convergence (Wei Ya Chassis/Samung Tube)
A convergence strip or two under the yoke facing that corner should correct that.
http://m.ebay.co.uk/itm/CRT-Convergence ... Ciid%253A2
http://m.ebay.co.uk/itm/CRT-Convergence ... Ciid%253A2
-
- Posts: 154
- Joined: March 20th, 2012, 1:47 pm
- Location: Ireland
- eBay: technofreek1
- Initials: OPM
Re: Convergence (Wei Ya Chassis/Samung Tube)
I used this stuff in mine, exact same monitor and chassis.
http://www.ebay.co.uk/itm/1-metre-1-2-1 ... XQvTlRirJc
http://www.ebay.co.uk/itm/1-metre-1-2-1 ... XQvTlRirJc
- Rossyra
- Supermod
- Posts: 7902
- Joined: February 12th, 2009, 1:24 am
- Location: UK
Re: Convergence (Wei Ya Chassis/Samung Tube)
In my experience plain magnets alter the geometry rather than convergence. Personally, I've had better results with strips of copper when going the DIY route for convergence tweaking.
It's still a lot of fannying about when you could just get the proper convergence strips for the sake of a few £.
It's still a lot of fannying about when you could just get the proper convergence strips for the sake of a few £.
-
- Posts: 154
- Joined: March 20th, 2012, 1:47 pm
- Location: Ireland
- eBay: technofreek1
- Initials: OPM
Re: Convergence (Wei Ya Chassis/Samung Tube)
Correct, in hindsight geometry is what I used it for primarily.Rossyra wrote:In my experience plain magnets alter the geometry rather than convergence.
-
- Posts: 124
- Joined: February 18th, 2012, 7:54 pm
- Location:
Re: Convergence (Wei Ya Chassis/Samung Tube)
Rossyra wrote:A convergence strip or two under the yoke facing that corner should correct that.
http://m.ebay.co.uk/itm/CRT-Convergence ... Ciid%253A2
I can get it a little better- but this travels across the lower 10% of the monitor. I can get the corners a little better, but not that whole bottom half.
Is there any trick to it that I'm missing?
- Rossyra
- Supermod
- Posts: 7902
- Joined: February 12th, 2009, 1:24 am
- Location: UK
Re: Convergence (Wei Ya Chassis/Samung Tube)
More strips?
-
- Posts: 124
- Joined: February 18th, 2012, 7:54 pm
- Location:
Re: Convergence (Wei Ya Chassis/Samung Tube)
I've tried with up to 8 haha.Rossyra wrote:More strips?
I guess the question is- with this chassis/yoke/tube combo- is it possible that this is as good as it'll get?
-
- Posts: 154
- Joined: March 20th, 2012, 1:47 pm
- Location: Ireland
- eBay: technofreek1
- Initials: OPM
Re: Convergence (Wei Ya Chassis/Samung Tube)
Maybe might be worth trying to fridge magnet next as they're pretty strong. See if you can get any correction at all.
Maybe grant might spot this thread and jump in with a suggestion too.
Maybe grant might spot this thread and jump in with a suggestion too.
- Rossyra
- Supermod
- Posts: 7902
- Joined: February 12th, 2009, 1:24 am
- Location: UK
Re: Convergence (Wei Ya Chassis/Samung Tube)
Christ, are you sure you're putting them in the right spot?
- grantspain
- Tech Head
- Posts: 4824
- Joined: August 17th, 2008, 4:23 pm
- Location: down south
Re: Convergence (Wei Ya Chassis/Samung Tube)
if its one quarter out then it could the yoke slightly out
proper convergence strips should be used to fine tune,you may need a few and they normally go right inside the yoke area rather than out
it is very painstaking getting convergence perfect
proper convergence strips should be used to fine tune,you may need a few and they normally go right inside the yoke area rather than out
it is very painstaking getting convergence perfect
-
- Posts: 124
- Joined: February 18th, 2012, 7:54 pm
- Location:
Re: Convergence (Wei Ya Chassis/Samung Tube)
grantspain wrote:if its one quarter out then it could the yoke slightly out
proper convergence strips should be used to fine tune,you may need a few and they normally go right inside the yoke area rather than out
it is very painstaking getting convergence perfect
When you say yoke slightly out- if I scoot out the rubber stoppers on the bottom and fit the yoke closer along the bottom, that should help, no? It's basically along the bottom up 10-20% ish.
I appreciate you guys' help with this.