I recently purchased a Blast City and was messing in the Factory menu of the ms-2931, but I kinda screwed up because I thought if i saved I could always revert back to factory default settings..but I can't.
Geometry is perfect but I kinda messed up the brightness and colors etc, and because there are so many options I can't get it looking good anymore.
So my question, can anyone with a ms-2931 give me their Factory settings for these settings?
R-CUTOFF
G-CUTOFF
B-CUTOFF
R-GAIN
G-GAIN
B-GAIN
ABL
C-CENTER
CONTRAST
BRIGHT
Thx in advance
Nanao MS-2931 Factory menu Default settings
-
- Please Continue...
- Posts: 4
- Joined: February 4th, 2012, 11:40 am
- Location:
- HyperBolt
- Please Continue...
- Posts: 95
- Joined: December 14th, 2009, 9:31 am
- Location: Las Vegas, Nevada
- eBay: rv9289
Re: Nanao MS-2931 Factory menu Default settings
Pardon me if I'm wrong, but I currently do not have my Blast City with me.
But I think I do remember an option to reset the settings to a default.
There should be an option called just "Reset". You hold the up or down button on this for like 5 seconds and it should go back to the default settings.
You might have to go to the extended menu to find it though.
To do that, without going into the menu at all, hold down and up for 5 seconds.
The wiki says you only have to hold down, but I always did it with up and down. I can't test it out, so try both if holding down doesn't work.
You'll know it worked when the menu comes up without pressing mode.
EDIT: You said you saved the settings?
I cannot check, so you may be stuck with those. Hopefully someone will bring you the setting values you need.
But I think I do remember an option to reset the settings to a default.
There should be an option called just "Reset". You hold the up or down button on this for like 5 seconds and it should go back to the default settings.
You might have to go to the extended menu to find it though.
To do that, without going into the menu at all, hold down and up for 5 seconds.
The wiki says you only have to hold down, but I always did it with up and down. I can't test it out, so try both if holding down doesn't work.
You'll know it worked when the menu comes up without pressing mode.
EDIT: You said you saved the settings?
I cannot check, so you may be stuck with those. Hopefully someone will bring you the setting values you need.
-
- Please Continue...
- Posts: 4
- Joined: February 4th, 2012, 11:40 am
- Location:
Re: Nanao MS-2931 Factory menu Default settings
Yup, I was messing around in the factory extended menu (The guy who I bought the cab from was so friendly to show me how to get in it ) and fooling around with the options to see what everything did (Didn't had the manual with it) but than I also saved all the settings with all colors and contrast etc messed up
I now have the manual downloaded but all those color settings etc are still a bit of Abracadabra for me, and when I edit one setting than the other settings seems to be wrong again...can't get it to look right at all.
So if someone got some decent settings for me it would be very helpful
I now have the manual downloaded but all those color settings etc are still a bit of Abracadabra for me, and when I edit one setting than the other settings seems to be wrong again...can't get it to look right at all.
So if someone got some decent settings for me it would be very helpful
- Wurstkopp
- Mister Dick Statue
- Posts: 744
- Joined: March 26th, 2009, 6:50 pm
- Location: Hamburg, Germany
- eBay: nachmittagsprogramm
- Initials: NIK
Re: Nanao MS-2931 Factory menu Default settings
There's an excellent thread bout getting the perfect picture in the wiki .
- crmb
- Please Continue...
- Posts: 45
- Joined: March 24th, 2012, 1:46 pm
- Location: France
Re: Nanao MS-2931 Factory menu Default settings
No one know about ABL ("automatic beam limiter" ??) and FH0 settings ?
-
- Posts: 2
- Joined: December 1st, 2022, 6:54 pm
- Location: Melbourne
- eBay: https://www.ebay.com.au/usr/re
Re: Nanao MS-2931 Factory menu Default settings
Did anyone ever track down the default settings for the MS-2931 or how to reset the saved data to default settings?
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Nanao MS-2931 Factory menu Default settings
30th option in the factory adjustment menu is Reset. Does that not work?
-
- Posts: 2
- Joined: December 1st, 2022, 6:54 pm
- Location: Melbourne
- eBay: https://www.ebay.com.au/usr/re
Re: Nanao MS-2931 Factory menu Default settings
I believe this just resets any unsaved changes, but not a reset back to defaults
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Nanao MS-2931 Factory menu Default settings
A-ha, I had no idea.