**CURRENTLY CLOSED** Marquee Group Order (Uni/NNC/Blast, Aero, NAC, AWSD/E2/3)

[Spectre]

Mine arrived while I was on holidays, and I picked them up at the post office on saturday.
Very pleased with the quality overall !
One minor complaint : the E2 ones were too wide, except the one with the Egret 2 logo. The other ones are too wide by about 8 millis, I will have to cut them a bit.

Hmm, sorry about that, might be due to the bleed area. If you'd be so kind as to measure the correct width for me I'll check my print sizes to make sure this doesn't happen again.

[Spectre]

Any interest in a new group order to close at the end of the month?

[kal20]

I’m interested

[FairWitness]

I’m interested too

[Benimaru]

Interested!

[parodius]

One minor complaint : the E2 ones were too wide, except the one with the Egret 2 logo. The other ones are too wide by about 8 millis, I will have to cut them a bit.

Hmm, sorry about that, might be due to the bleed area. If you'd be so kind as to measure the correct width for me I'll check my print sizes to make sure this doesn't happen again.

Correct one should be 40x27.2, the ones that were too big were 40.7x27.6.

[landisama]

Interested

[Spectre]

Correct one should be 40x27.2, the ones that were too big were 40.7x27.6.

Thanks for that, I'll check my templates. I think maybe your prints had more of the bleed area than is typical, but perhaps I need to bring them in a little bit to account for this.

[Spectre]

The 19th group order is now OPEN - closing midnight on Wednesday 31st October.

As always, please note that the closing date may be pushed back depending on interest level. Post any new design requests here in the thread and I will fill as many as I can before the order closes.

Please go to http://spectre.myartsonline.com to browse the catalogue of marquees!
Updated July 2018, 333 designs across 7 different formats! Please browse the last few pages of the thread for any new designs which I've not yet added to the catalogue.

I also have some marquees in stock, these are available for immediate dispatch or can be reserved now, ready to be sent with your order. See the stock list in post 3.

[speedswan]

Hello,

I'd like the following marquees

e2awsd_ikaruga-a
e2awsd_ikaruga-b
e2awsd_ikaruga-c
e2awsd_unsquadron
nac_bubblebobble
nac_salamander
nac_salamander2
bubblebobble
gradius
gradiusiv
rtype
smashtv

Shipped to the USA please.

Thanks!

Mark

[landisama]

Hi Spectre,

I want to order for my Blast City:
-streetfighter2

Can you also make a Final Fight marquee for Blast with the artwork of nac_finalfight-a ?
Also interested in a Virtua FIghter Remix marquee, if possible in this short amount of time.
Thanks a lot,
Andrei

[Spectre]

Hi Spectre,

I want to order for my Blast City:
-streetfighter2

Can you also make a Final Fight marquee for Blast with the artwork of nac_finalfight-a ?
Also interested in a Virtua FIghter Remix marquee, if possible in this short amount of time.
Thanks a lot,
Andrei

Hi Andrei, both of those should be possible

[Benimaru]

I would like to order the following backlit uniblast marquees:

radiantsilvergun-c
ikaruga-b
gigawing2

Shipped to germany

Many thanks in advance for your efforts!

[Rezwalker]

tetristgm-a
ddpsdoj_monouchi
tetristgm-b
ddpdfkbl

nac_ddpdoj_softdrink
nac_esprade
nac_espgaluda

e2awsd_ddpsdoj
e2awsd_ketsui
e2awsd_mushihime-c
e2awsd_guwange
e2awsd_deathsmiles
e2awsd_espgaluda2

And could you do a Tetris TGM 2 & 3 for uniblast ?

thx

Rez

[8bitforlife]

Hello specter I'm finally ready to order a couple marquees. Finally got my blasts freighted to me in Hawaii.

Sega blast city
order code: blacktiger
order code: bubblebobble
order code: daimakaimura

e2awsd_moonwalker but for blast city?

Id like to get more but money is tight.

Could you look into making a xexex, Spider-Man and fighter & attacker (f/a in Japan) marquee for Sega blast city please.

[kal20]

Spectre

is it possible to cute_Progear-b for NAC?

Thanks

[kal20]

Spectre

is it possible to cute_Progear-b for NAC?

Thanks

[Spectre]

And could you do a Tetris TGM 2 & 3 for uniblast ?

Not sure, but I'll certainly take a look for you

[Spectre]

Spectre

is it possible to cute_Progear-b for NAC?

Thanks

Sure, no problem. Please note you'll need to also pick a second NAC marquee as the minimum order quantity is 2 pieces on non-backlits.

[kal20]

Spectre

is it possible to cute_Progear-b for NAC?

Thanks

Sure, no problem. Please note you'll need to also pick a second NAC marquee as the minimum order quantity is 2 pieces on non-backlits.

Second: nac_dodonpachi