Page 1 of 5

FS - Repro Marquee Holders (Vewlix, Astro City, Egret, AWSD, Naomi Universal, (New) Net City)

Posted: October 18th, 2018, 10:50 pm
by ckong
I make repro Marquee Holders for several Candy Cab types, see the list below for the ones that are available right now. :D And if there is enough interest I can make others too. At least, as long as I can get my hands on the original marquee holder to recreate a faithful reproduction, or if someone can give accurate measurements.

Prices of the Repro Marquee Holders, ready to order now :D :

1. Vewlix (design A) > € 55
2. Vewlix (design B) > € 45
3. (New) Astro City and Astro City 2 (design A)> € 45,00
4. (New) Astro City and Astro City 2 (design B)> € 45,00
5. Egret II / Egret 3 / AWSD > € 40
6. Naomi Universal / Net City / New Net City > € 50
7. Capcom Cute > € 45
8. Super Neo 29 / Super Neo 29 Candy > € 55
9. Super Neo 29 Type II € 65
10. Capcom Impress > € 50
11. Universal City (Chinese New Astro City clone) > € 45
12. Sega Versus City > € 55

Mounting bolts and dome nuts are included, but shipping from The Netherlands is additional.

Shipping costs
- shipping costs in The Netherlands is € 7 (max. 10kg)
- shipping costs to most countries in Europe is € 15.50 for one marquee holder and € 22 for two or three marquee holders (the same or mixed).
- shipping to USA, Canada and other countries outside Europe is € 26.80 for one marquee holder and € 36.80 for two or three marquee holders (the same or mixed).

For shipping costs of Naomi Universal / Net City / New Net City and the Super Neo 29 Type II marquee holders, please contact me. These marquee holders are much heavier than the other ones.

All marquee holders come with protection foil (both sides), which can be removed easily. I will make them on order or in small batches, so please give me a week or so after payment to ship them out. Payment has to be made through Paypal, gift or otherwise. Paypal fees will be paid by the buyer. You can read my feedback in this forum.

Specs:

1. Vewlix Marquee Holder (design A). Lasercut from a piece of 5mm thick clear acrylic for the backpanel and a thin 0.75mm clear film for the frontpanel, just like the original marquee holder. It is the best reproduction of the original that you can get (see the images below). It comes with:

- 5 Stainless Steel A2 M4 x 8mm Allen button head screws
- 2 Stainless Steel A2 M4 x 12mm Allen button head screws
- 5 Stainless Steel A2 M4 dome nuts


2. Vewlix Marquee Holder (design B). Lasercut from 3mm and 2mm clear acrylic, making it 5mm thick. The marquee holder is a faithful reproduction of the original. It comes with:

- 5 Stainless Steel A2 M4 x 8mm Allen button head screws
- 2 Stainless Steel A2 M4 x 12mm Allen button head screws
- 5 Stainless Steel A2 M4 dome nuts


3. (New) Astro City / Astro City 2 Marquee Holder (design A). Lasercut from 1 piece of 4mm thick clear acrylic for the frontpanel and a thin 0.5mm thin clear film for the backpanel, just like the original. Because of this thin film, the marquee holder is an almost identical reproduction of the original and it includes two square mounting supports. I will send the mounting supports loose with the marquee holder, so you can decide yourself if you want to mount the marquee holder with or without a gap. It comes with:

- 2 Stainless Steel A2 M4 x 8mm Allen button head screws
- 2 Stainless Steel A2 M4 x 16mm Allen button head screws
- 2 Stainless Steel A2 M4 dome nuts
- 2 mounting supports, each 4mm thick clear acrylic with 3M 467MP adhesive tape on one side


4. (New) Astro City / Astro City 2 Marquee Holder (design B). Lasercut from 2 pieces of 2mm clear acrylic, making it 4mm thick. The marquee holder is a faithful reproduction of the original and it includes two square mounting supports. I will send the mounting supports loose with the marquee holder, so you can decide yourself if you want to mount the marquee holder with or without a gap. It comes with:

- 2 Stainless Steel A2 M4 x 8mm Allen button head screws
- 2 Stainless Steel A2 M4 x 16mm Allen button head screws
- 2 Stainless Steel A2 M4 dome nuts
- 2 mounting supports, each 4mm thick clear acrylic with 3M 467MP adhesive tape on one side


5. Egret II / Egret 3 / Sammy Atomiswave Marquee Holder. Lasercut from 2 pieces of 2mm clear acrylic, making it 4mm thick. The marquee holder is a faithful reproduction of the original and it comes with:

- 5 Stainless Steel A2 M4 x 8mm Allen button head screws
- 3 Stainless Steel A2 M4 dome nuts
- 2 Stainless Steel M4 washers


6. Naomi Universal / Net City / New Net City Marquee Holder. Lasercut from two pieces of 3mm clear acrylic, making it 6mm thick. The marquee holder is a faithful reproduction of the original and it comes with:

- 6 Stainless Steel A2 M4 x 8mm Allen button head screws
- 2 Stainless Steel A2 M4 x 16mm Allen button head screws
- 6 Stainless Steel A2 M4 dome nut


7. Capcom Cute Marquee Holder. Lasercut from two pieces of 3mm clear acrylic, making it 6mm thick. The marquee holder is a faithful reproduction of the original, including the Capcom logo. It comes with:

- 3 Stainless Steel A2 M4 x 10mm Allen button head screws
- 1 Stainless Steel A2 M4 dome nut
- 2 Stainless Steel M4 washers


8. Super Neo 29 / Super Neo 29 Candy Marquee Holder. Lasercut from two pieces of 3mm clear acrylic and 2 white acrylic strips, making it 6mm thick. The marquee holder is a faithful reproduction of the original and it comes with:

- 6 Stainless Steel A2 M4 x 10mm Allen button head screws
- 2 Stainless Steel A2 M4 dome nuts


9. Super Neo 29 Type II Marquee Holder. Lasercut from two pieces of 3mm clear acrylic and 2 white acrylic strips, making it 6mm thick. The marquee holder is a faithful reproduction of the original and it comes with:

- 6 Stainless Steel A2 M4 x 10mm Allen button head screws
- 2 Stainless Steel A2 M4 dome nuts


10. Capcom Impress MArquee Holder. Lasercut from two pieces of 3mm clear acrylic, making it 6mm thick. The marquee holder is a faithful reproduction of the original and it comes with:

- 2 Stainless Steel A2 M4 x 10mm Allen button head screws
- 2 Stainless Steel A2 M4 x 12mm Allen button head screws
- 4 Stainless Steel A2 M4 dome nuts


11. (New) Universal City Marquee Holder (Chinese clone of New Astro City). Lasercut from 2 pieces of 2mm clear acrylic, making it 4mm thick. Apparently this game cabinet has no original marquee holder and I made this one on request. It is based on the one for the NAC but the cab mounting holes are placed differently. It also doesn't have mounting supports. The marquee holder comes with:

- 2 Stainless Steel A2 M4 x 8mm Allen button head screws
- 3 Stainless Steel A2 M4 x 16mm Allen button head screws
- 2 Stainless Steel A2 M4 dome nuts

12. Sega Versus City. Lasercut from 2 pieces of 4mm clear acrylic, making it 8mm thick. Like the original marquee holder this reproduction also has a center piece which is made of a 0.3mm thin white polyester sheet, without printed artwork. The marquee holder comes with:

- 2 Stainless Steel A2 M4 x 12mm Allen button head screws
- 2 Stainless Steel A2 M4 x 16mm Allen button head screws
- 2 Stainless Steel A2 M4 dome nuts


Here are some pictures of a few marquee holders that were made recently:


Vewlix (design A)


Image

Image

Image


Vewlix (design B)


Image


Egret / AWSD


Image

Image


(New) Astro City / Astro City 2 (design A)


Image


(New) Astro City / Astro City 2 (design B)


Image


NeoGeo Super Neo 29 / Super Neo 29 Candy


Image

Image

Image


Capcom Impress


Image

Image


Capcom Cute


Image


(New) Net City / Universal


Image

Image


NeoGeo Super Neo 29 Type II


Image

Image


Sega Versus city


Image

Image

Re: FS - Repro Marquee Holders

Posted: October 19th, 2018, 12:55 am
by siyco
As before I'm in il take a vewlix off you MP the details to purchase one

Re: FS - Repro Marquee Holders

Posted: October 19th, 2018, 5:22 pm
by kal20
MP sent

Re: FS - Repro Marquee Holders

Posted: October 19th, 2018, 6:21 pm
by glocknyne562
Will send you a MP

Re: FS - Repro Marquee Holders

Posted: October 21st, 2018, 8:33 pm
by waiwainl
Nice to see you back in the forums! Great product also :D

Re: FS - Repro Marquee Holders

Posted: October 22nd, 2018, 6:02 am
by 8bitforlife
Hi would you be interested in making windy 1/2 marquees?

Re: FS - Repro Marquee Holders

Posted: October 22nd, 2018, 8:36 am
by ckong
waiwainl wrote:
October 21st, 2018, 8:33 MP
Nice to see you back in the forums! Great product also :D
Never been back. LOL ;) But my presence was very low-key. :)

Re: FS - Repro Marquee Holders

Posted: October 22nd, 2018, 10:06 am
by ckong
8bitforlife wrote:
October 22nd, 2018, 6:02 am
Hi would you be interested in making windy 1/2 marquees?
That one is hard to do in any way, but certainly not with the laser cutter. What I could do is cut the outline and the holes for the bolts from two flat sheets of plexi, so it has the same shape. But that would hardly be a repro of the orignal marquee, with its rounded edges, molded 3D enforcement etc.

Re: FS - Repro Marquee Holders

Posted: October 23rd, 2018, 7:08 pm
by ckong
Never mind

Re: FS - Repro Marquee Holders

Posted: October 26th, 2018, 9:20 pm
by ckong
The first few marquee holders are done, which gave me the opportunity to calculate the shipping costs exactly. I added this info to the first post. :)

Re: FS - Repro Marquee Holders

Posted: October 26th, 2018, 10:43 pm
by wesker
Do you have marquee fie nnc Naomi ?

Thanx

Re: FS - Repro Marquee Holders

Posted: October 27th, 2018, 7:29 am
by ckong
I have the drawing for the Naomi Universal, which is the same as the Net City and New Net City. The repro marquee holder will be made of 2 sheets of 3 mm acrylic and comes with the nuts and bolts needed for mounting. Price is € 50 excluding shipping.
wesker wrote:
October 26th, 2018, 10:43 MP
Do you have marquee fie nnc Naomi ?

Thanx

Re: FS - Repro Marquee Holders

Posted: October 27th, 2018, 11:05 pm
by bagheera369
Really interested in 2 AWSD's, and a NAC....let me get a couple things sold, and I'll bite the bullet.

Re: FS - Repro Marquee Holders

Posted: October 28th, 2018, 10:21 am
by ckong
bagheera369 wrote:
October 27th, 2018, 11:05 MP
Really interested in 2 AWSD's, and a NAC....let me get a couple things sold, and I'll bite the bullet.
:D That's good to hear. Take your time, stock is unlimted as I make them on order.

WIP, Astro marquee holder >

Re: FS - Repro Marquee Holders

Posted: October 30th, 2018, 12:43 pm
by badtz
Hello.

Do you think you will be able to make a marquee for the Sega Swing ?
I can send you an original (with broken corner as usual)

Re: FS - Repro Marquee Holders

Posted: October 30th, 2018, 2:07 pm
by ckong
badtz wrote:
October 30th, 2018, 12:43 MP
Hello.

Do you think you will be able to make a marquee for the Sega Swing ?
Might be. Could you post a picture of the part that needs to be replaced, so that I get more of an idea what is needed? Would be great. :)

Re: FS - Repro Marquee Holders

Posted: October 30th, 2018, 2:36 pm
by badtz
It looks like this

Image

Re: FS - Repro Marquee Holders

Posted: October 30th, 2018, 5:03 pm
by ckong
thx for the picture. Let's discuss this further via MP.

Re: FS - Repro Marquee Holders

Posted: October 31st, 2018, 12:15 am
by wesker
ckong wrote:
October 27th, 2018, 7:29 am
I have the drawing for the Naomi Universal, which is the same as the Net City and New Net City. The repro marquee holder will be made of 2 sheets of 3 mm acrylic and comes with the nuts and bolts needed for mounting. Price is € 50 excluding shipping.
wesker wrote:
October 26th, 2018, 10:43 MP
Do you have marquee fie nnc Naomi ?

Thanx
Hello do you have a photo of it?

Re: FS - Repro Marquee Holders

Posted: October 31st, 2018, 10:50 am
by ckong
wesker wrote:
October 31st, 2018, 12:15 am
ckong wrote:
October 27th, 2018, 7:29 am
I have the drawing for the Naomi Universal, which is the same as the Net City and New Net City. ....
Hello do you have a photo of it?
Here is a picture, not mine, but from FrancoB. The marquee holder that I make is regarding the dimensions and material the same, but from clear acrylic. And the acrylic will be plain, without text. :)