Blast City kick harness wiring

Arcade cabinet hardware and accessories
Post Reply
User avatar
Prosolis
Please Continue...
Posts: 32
Joined: December 18th, 2009, 1:52 am
Location: Atlanta
eBay: reala311

Blast City kick harness wiring

Post by Prosolis »

Hey guys. I've tried reading the old posts on this topic but none of them are very clear (or perhaps I'm thick). :? Currently, I'm under the assumption that I must wire up a kick harness from the option connector located inside the control panel beside the 1P connector to the connector on the terminal board inside the cab here:

Image

Is this correct? If so, How do I get button 6 from p1/p2 through to the Sega I/O board since button 6 supposedly (from the wiring diagrams) isn't passed through on the JAMMA connector? :think:
User avatar
Prosolis
Please Continue...
Posts: 32
Joined: December 18th, 2009, 1:52 am
Location: Atlanta
eBay: reala311

Re: Blast City kick harness wiring

Post by Prosolis »

reworded a bit since my original post wasn't clear..
User avatar
penrhos
Panel Beater
Posts: 1477
Joined: September 11th, 2008, 12:08 pm
Location: Leicester - UK
eBay: ngpd002

Re: Blast City kick harness wiring

Post by penrhos »

As far as I remember the oblong connector under the CP is where the kick loom is connected to the buttons on the CP and you have a CPS2 kick harness and a connector that fits to the PCB on the side of the cash box.

Unfortunatley I haven't had or seen the correct loom.

Its the same if you have the JVS/JAMMA -001 loom - it only has buttons 1-4 wired up to the plugs under the CP.
2 * Vewlix Diamond Blacks,2 * Vewlix-F, 1 * Sega Rally 3, 1 * Video Pinball, 1 * DinoKing (JAMMA Converted).
User avatar
Prosolis
Please Continue...
Posts: 32
Joined: December 18th, 2009, 1:52 am
Location: Atlanta
eBay: reala311

Re: Blast City kick harness wiring

Post by Prosolis »

Thanks for the response, penrhos. One more question and I think I'm good. How did you wire your kick buttons to the Sega JVS I/O? Did you modify the Jamma harness or solder directly to the Sega I/O for buttons 4/5 and use CN3 (I believe) for button 6? Only buttons 1-3 work for me in the JVS test screen and I'm using the -001 harness.
User avatar
Prosolis
Please Continue...
Posts: 32
Joined: December 18th, 2009, 1:52 am
Location: Atlanta
eBay: reala311

Re: Blast City kick harness wiring

Post by Prosolis »

Nevermind.. I'm buying a Capcom I/O board instead. :think:
User avatar
scogon
Please Continue...
Posts: 87
Joined: September 15th, 2008, 1:40 pm
Location: Ottawa, Canada

Re: Blast City kick harness wiring

Post by scogon »

Prosolis wrote:Hey guys. I've tried reading the old posts on this topic but none of them are very clear (or perhaps I'm thick). :? Currently, I'm under the assumption that I must wire up a kick harness from the option connector located inside the control panel beside the 1P connector to the connector on the terminal board inside the cab here:

Image

Is this correct? If so, How do I get button 6 from p1/p2 through to the Sega I/O board since button 6 supposedly (from the wiring diagrams) isn't passed through on the JAMMA connector? :think:
Anyone know the pinout this? I'll continue to look and will post it if I find it.
User avatar
scogon
Please Continue...
Posts: 87
Joined: September 15th, 2008, 1:40 pm
Location: Ottawa, Canada

Re: Blast City kick harness wiring

Post by scogon »

ok, sorted out the pin out for this I/O.

8 - Ground
7 - ?
6 - P2 Heavy Kick
5 - P1 Heavy Kick
4 - P2 Medium Kick
3 - P1 Medium Kick
2 - P2 Light Kick
1 - P1 Light Kick

Generic 8 pin molex connector fits this just fine, so it's easy to terminate your CPS2 Kick harness directly to this IO.
User avatar
penrhos
Panel Beater
Posts: 1477
Joined: September 11th, 2008, 12:08 pm
Location: Leicester - UK
eBay: ngpd002

Re: Blast City kick harness wiring

Post by penrhos »

CPS1/CPS2 you would want the standard kick loom for CPS2 but the other end would have an 8*1 molex wired for the Sega pinout - This would also work with the Capcom JVS-JAMMA adapter.

For a J-PAC you would wire the 8*1 molex to the screw terminals.

For a Sega V1 i/o you would take button 6 to CN3 the rest are available on the JAMMA connector (but your looms would have to have buttons 1-5 wired in).
2 * Vewlix Diamond Blacks,2 * Vewlix-F, 1 * Sega Rally 3, 1 * Video Pinball, 1 * DinoKing (JAMMA Converted).
User avatar
codecrank
Please Continue...
Posts: 466
Joined: January 9th, 2011, 7:32 pm
Location: NSA Central

Re: Blast City kick harness wiring

Post by codecrank »

I'm trying to locate the correct 8pin header/cable too. I'm looking at JST 8pin connectors, but there are so many different models, each with a combination of different sizes, pitch, distance between pins ,etc ,etc . Does anyone have a part number for this ? that would REALLY help.

thanks !
User avatar
davewellington
The Librarian
Posts: 1389
Joined: July 7th, 2010, 1:42 am
Location: Wellington, New Zealand
Initials: DAV

Re: Blast City kick harness wiring

Post by davewellington »

Incase someone doesn't know the part number/name, I suggest just taking the board into your local electronics shop and asking. I often do this - "I need a replacement for.... this!" and they'll go off and find it for me :)
all your wiki pages belong to me
User avatar
codecrank
Please Continue...
Posts: 466
Joined: January 9th, 2011, 7:32 pm
Location: NSA Central

Re: Blast City kick harness wiring

Post by codecrank »

Ok, I just built the cable for this, you need a Molex 2695 serie connector.
IMAG0590.jpg
http://www.molex.com/pdm_docs/sd/022012027_sd.pdf"

perfect fit. I bought one and the pins I needed here:

http://www.jammaboards.com/store/connec ... cat_9.html"
You do not have the required permissions to view the files attached to this post.
User avatar
OtokonoZenyou
Please Continue...
Posts: 73
Joined: October 11th, 2010, 4:41 am
Location: Nashville, TN. USA
eBay: hayato3d
Initials: ALK

Re: Blast City kick harness wiring

Post by OtokonoZenyou »

codecrank wrote:Ok, I just built the cable for this, you need a Molex 2695 serie connector.
IMAG0590.jpg
http://www.molex.com/pdm_docs/sd/022012027_sd.pdf"

perfect fit. I bought one and the pins I needed here:

http://www.jammaboards.com/store/connec ... cat_9.html"
Thanks for the info, just bought what I needed from them as well. Got some PCB legs while I was at it too, been needing some, decent price.
User avatar
codecrank
Please Continue...
Posts: 466
Joined: January 9th, 2011, 7:32 pm
Location: NSA Central

Re: Blast City kick harness wiring

Post by codecrank »

scogon wrote:ok, sorted out the pin out for this I/O.

8 - Ground
7 - ?
6 - P2 Heavy Kick
5 - P1 Heavy Kick
4 - P2 Medium Kick
3 - P1 Medium Kick
2 - P2 Light Kick
1 - P1 Light Kick

Generic 8 pin molex connector fits this just fine, so it's easy to terminate your CPS2 Kick harness directly to this IO.
actually:

8 - P2 Ground
7 - P1 Ground
6 - P2 Heavy Kick
5 - P1 Heavy Kick
4 - P2 Medium Kick
3 - P1 Medium Kick
2 - P2 Light Kick
1 - P1 Light Kick


I just had to modify the cable I built to add a ground for P1
Post Reply