The Sega Aero city is quite a popular candy cab and I would like to reproduce the marquee holder for both the 'Japanese' Aero and the Aero with the different marquee holder which was produced for the European market. I don't have the marquee holders at hand, but maybe someone could take some measurements?
This is the info that I need for the 'Japanese' marquee holder (red lines A - J):
And this for the 'Europese' marquee holder:
Please notice that A should be measured between the green guide lines. The measurements D through H are most important and should be accurate. And the measurements involving the holes should be measured from the center of the holes. And what is the diameter of the bottom holes (I don't know if the original marquee holder has holes behind the top metal clips, but I will use M4 bolts instead of the clips). If possible I would like measurements in mm's.
I will make the marquee holders with the beveled edge, like the original marquee holders have too.
Thx in advance.
Sega Aero City marquee holder - measurements needed
- ckong
- Please Continue...
- Posts: 176
- Joined: August 18th, 2008, 8:47 pm
- Location: The Netherlands
Sega Aero City marquee holder - measurements needed
You do not have the required permissions to view the files attached to this post.
- FrancoB
- J+ member of the year finalist!
- Posts: 4758
- Joined: June 8th, 2009, 10:42 pm
- Location: Oxfordshire
- eBay: francosquashking
- Initials: FRN
Re: Sega Aero City marquee holder - measurements needed
I'm back home again a week on Wednesday (30th Oct). If you can wait until then I can create .dfxs of both of them for you.
- ckong
- Please Continue...
- Posts: 176
- Joined: August 18th, 2008, 8:47 pm
- Location: The Netherlands
-
- Please Continue...
- Posts: 4
- Joined: December 3rd, 2018, 9:34 pm
- Location: France
- eBay: kumokuma2011
- Initials: ZDX
Re: Sega Aero City marquee holder - measurements needed
Hi.
I am working on my aero city and I have access to lazer cutting and acrylic cutting power tools I would like to do the same.
Can some of you share the measurements for bot Marquee Holder please ?
Best regards
AIR.
I am working on my aero city and I have access to lazer cutting and acrylic cutting power tools I would like to do the same.
Can some of you share the measurements for bot Marquee Holder please ?
Best regards
AIR.
- arcadista
- Posts: 61
- Joined: October 20th, 2015, 3:13 am
- Location: Buenos Aires
- Initials: AIL
Re: Sega Aero City marquee holder - measurements needed
ckong wrote: ↑October 21st, 2019, 11:51 am The Sega Aero city is quite a popular candy cab and I would like to reproduce the marquee holder for both the 'Japanese' Aero and the Aero with the different marquee holder which was produced for the European market. I don't have the marquee holders at hand, but maybe someone could take some measurements?
This is the info that I need for the 'Japanese' marquee holder (red lines A - J):
Aero City (Japanese. Style) Needed measurements.PNG
And this for the 'Europese' marquee holder:
Aero City (Euro Style) Needed measurements.PNG
Please notice that A should be measured between the green guide lines. The measurements D through H are most important and should be accurate. And the measurements involving the holes should be measured from the center of the holes. And what is the diameter of the bottom holes (I don't know if the original marquee holder has holes behind the top metal clips, but I will use M4 bolts instead of the clips). If possible I would like measurements in mm's.
I will make the marquee holders with the beveled edge, like the original marquee holders have too.
Thx in advance.
Hi! I will edit this post with pictures later. But for japanese marquee holder, line A is 40cm and line J is 30cm.