Outzone pcb won’t coin up! (Fixed)
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Outzone pcb won’t coin up! (Fixed)
I just got this outzone for a steal. I took a chance since it was sitting on a shelf and it works flawlessly !!.....that is until you try to coin up
Anyone have any experience /ideas where to look here? I tried jumping the coin switch on the Jamma connector and it coins up that way.
Anyone have any experience /ideas where to look here? I tried jumping the coin switch on the Jamma connector and it coins up that way.
You do not have the required permissions to view the files attached to this post.
Last edited by Hrvat9 on December 9th, 2021, 4:59 am, edited 3 times in total.
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Re: Outzone pcb won’t coin up!
Should have checked this right away
You do not have the required permissions to view the files attached to this post.
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa
- emphatic
- Breastfeeds when required
- Posts: 5874
- Joined: April 7th, 2009, 4:14 pm
- Location: Alingsås, Sweden
- eBay: jorgen_sjolander
- Initials: JOR
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Outzone pcb won’t coin up!
So it's a problem with your cab, and not the board? Is your coin switch stuck? If it's a 3-legged switch, is the connector on 'NO / normally open' or 'NC / normally closed'? Check continuity between pin 16 and GND on the jamma edge connector.
Also, if you don't care for punching in credits, there's a free play patch for the game made by @mikejmoffitt:
https://github.com/Mikejmoffitt/outzone-freeplay
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Re: Outzone pcb won’t coin up!
My Nac coins up every other pcb I have except this one , it’s gotta be with the board
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Re: Outzone pcb won’t coin up!
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa
- emphatic
- Breastfeeds when required
- Posts: 5874
- Joined: April 7th, 2009, 4:14 pm
- Location: Alingsås, Sweden
- eBay: jorgen_sjolander
- Initials: JOR
Re: Outzone pcb won’t coin up!
I thought the TEST mode COIN2 OFF photo was a clue and you'd solved it. I did not intend to poke fun.
My games: http://www.emphatic.se
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
- Sunder
- Posts: 325
- Joined: August 31st, 2017, 12:13 pm
- Location: Slovakia
- eBay: sunderaj82
- Initials: SUN
Re: Outzone pcb won’t coin up!
How many pins are there on the coin switch?
- Sunder
- Posts: 325
- Joined: August 31st, 2017, 12:13 pm
- Location: Slovakia
- eBay: sunderaj82
- Initials: SUN
Re: Outzone pcb won’t coin up!
My guess is coin switch is wired up to be always on. So when you press it goes off, by the looks of it. Board probably has problems seeing that. As evident by that test screen.
- Flyingfistofbudha
- Posts: 86
- Joined: December 8th, 2016, 10:05 pm
- Location: U.k.
- eBay: Daniels4249
- Initials: Dan
Re: Outzone pcb won’t coin up!
Wire up a button to coin 2 on jamma edge
And set coin 2 to on
And try adding coins there.
And set coin 2 to on
And try adding coins there.
-
- Posts: 28
- Joined: May 28th, 2012, 2:35 am
- Location: Tokyo, Japan
- eBay: 7raster
Re: Outzone pcb won’t coin up!
Check the 74LS240s near the edge, sometimes an input gets stuck. Could also be a bad resistor network for pull-up.
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Re: Outzone pcb won’t coin up!
This is what I’m looking for , but I can’t figure out which one . How would I find the resistor network? Continuity to ground? I guess for the 74ls, I’d be looking up the Pinot and seeing if anything is ground or open?mikejmoffitt wrote: ↑December 29th, 2020, 11:47 pm Check the 74LS240s near the edge, sometimes an input gets stuck. Could also be a bad resistor network for pull-up.
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa
- nem
- Needs a custom rank
- Posts: 2776
- Joined: August 17th, 2008, 6:59 pm
- Location: Finland
Re: Outzone pcb won’t coin up!
??
Are you still getting it to coin up by jumping the coin switch on the jamma connector?
Are you still getting it to coin up by jumping the coin switch on the jamma connector?
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Re: Outzone pcb won’t coin up!
Yup! Or I just press the service button on my NAC
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Re: Outzone pcb won’t coin up!
No worries
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa
-
- Posts: 191
- Joined: April 26th, 2017, 3:47 pm
- Location: Canada
- eBay: hrvaat
Re: Outzone pcb won’t coin up!
Fixed! i was pointed In the right direction with a schematic and got the coin up sorted socketed and a new LS240
You do not have the required permissions to view the files attached to this post.
candy: Sega New Astro City x2, Sega Versus City (sold)
Seeeegggggaaaaaa
Seeeegggggaaaaaa