cps2 Screen does not appear
- kobayuz777
- Please Continue...
- Posts: 54
- Joined: June 1st, 2018, 3:16 am
- Location: japan
- eBay: koba27300036
cps2 Screen does not appear
I repaired the battery but the screen is not displayed.
I hear the sound.
I also responded to buttons. You can play the game.
However, only the screen does not come out. Is there a person who understands the cause?
I was committed suicide with running out of batteries,
Since I was able to recover, I seem to be able to send program signals etc. normally.
If the screen is disturbed, we suspect contact failure of the IC chip (eg DL - 1927) etc.
However, the screen does not show up at all,
Is the video signal broken somewhere?
- leonardoliveira
- Please Continue...
- Posts: 692
- Joined: August 30th, 2012, 5:53 am
- Location: Brazil
- Initials: leo
Re: cps2 Screen does not appear
Have you tested a different BGSB3 PAL chip? If it malfunctions graphics roms will not receive chip select signals and thus no data will be possible to be read, which will cause blank screen.
- pulstar
- Posts: 166
- Joined: March 9th, 2013, 6:57 pm
- Location: Southampton, United Kingdom
Re: cps2 Screen does not appear
I had a similar solid colour screen before and it turned out to be the ls245s just below the battery so it might be worth checking they're functioning as expected. Hopefully it isn't one of the customs.
- kobayuz777
- Please Continue...
- Posts: 54
- Joined: June 1st, 2018, 3:16 am
- Location: japan
- eBay: koba27300036
Re: cps2 Screen does not appear
thank you for the advice!leonardoliveira wrote: ↑September 12th, 2018, 1:49 pm Have you tested a different BGSB3 PAL chip? If it malfunctions graphics roms will not receive chip select signals and thus no data will be possible to be read, which will cause blank screen.
I exchanged the PAL of SSFXJ which is working normally.
But the results were the same. In the same way a red blank screen appears.
It may be a different cause.
- kobayuz777
- Please Continue...
- Posts: 54
- Joined: June 1st, 2018, 3:16 am
- Location: japan
- eBay: koba27300036
Re: cps2 Screen does not appear
thank you for the advice!
Is this around here? Do you measure the voltage with a tester?
Did your board fix up when you replaced this?
- pulstar
- Posts: 166
- Joined: March 9th, 2013, 6:57 pm
- Location: Southampton, United Kingdom
Re: cps2 Screen does not appear
That's the two you circled there.
You'll need a logic probe or, preferably, an oscilloscope to test them properly and you'll need the data sheet to understand what the pins should be doing.
I replaced one of those and the issue went away, can't remember which one it was that needed changing though but if its faulty you should be able to tell with the probe/scope.
You'll need a logic probe or, preferably, an oscilloscope to test them properly and you'll need the data sheet to understand what the pins should be doing.
I replaced one of those and the issue went away, can't remember which one it was that needed changing though but if its faulty you should be able to tell with the probe/scope.
- kobayuz777
- Please Continue...
- Posts: 54
- Joined: June 1st, 2018, 3:16 am
- Location: japan
- eBay: koba27300036
Re: cps2 Screen does not appear
pulstar wrote: ↑September 13th, 2018, 9:40 am That's the two you circled there.
You'll need a logic probe or, preferably, an oscilloscope to test them properly and you'll need the data sheet to understand what the pins should be doing.
I replaced one of those and the issue went away, can't remember which one it was that needed changing though but if its faulty you should be able to tell with the probe/scope.
I see,
I have a logic probe. However, since there is no data sheet, we will compare the behavior of LS 245 of normal board B and this broken board.
If you know, please let me know,
Is there any information on the data sheet somewhere?
- pulstar
- Posts: 166
- Joined: March 9th, 2013, 6:57 pm
- Location: Southampton, United Kingdom
Re: cps2 Screen does not appear
The data sheet for a DIP 74LS245 will be fine.
- kobayuz777
- Please Continue...
- Posts: 54
- Joined: June 1st, 2018, 3:16 am
- Location: japan
- eBay: koba27300036
Re: cps2 Screen does not appear
Mr, leonardoliveira,
Mr. pulstar,
thank you for the advice!
t took time,
Recently I bought a heat gun. If I exchange 74 ls 245 for a new commercial item
I got repaired! I am deeply impressed!
However,
I investigated the signal at the logic probes, but I did not understand well.
(I was able to check the signals such as "high" and "low", but is it correct?
I do not understand)
I do not understand, so I have to study further.
- pulstar
- Posts: 166
- Joined: March 9th, 2013, 6:57 pm
- Location: Southampton, United Kingdom
Re: cps2 Screen does not appear
Excellent work. Glad to see you got the game working.
-
- Posts: 573
- Joined: April 17th, 2013, 5:16 pm
- Location: Netherlands
- eBay: asure_nl
Re: cps2 Screen does not appear
Just piggybacking along for a ride on this thread.
I have a similar issue with a B board, except the sprite layer comes and goes if i move my hand around in this area like a magician.. I was suspecting the big chip near the battery since touching it makes the layer appear (and stay solid), but it randomly comes & goes. I should give those 245's a check up as well right?
I have a similar issue with a B board, except the sprite layer comes and goes if i move my hand around in this area like a magician.. I was suspecting the big chip near the battery since touching it makes the layer appear (and stay solid), but it randomly comes & goes. I should give those 245's a check up as well right?
- NoAffinity
- Posts: 386
- Joined: January 8th, 2017, 3:46 pm
- Location: Escondido, CA, USA
- eBay: noaffinity
- Initials: CSG
- Contact:
- pulstar
- Posts: 166
- Joined: March 9th, 2013, 6:57 pm
- Location: Southampton, United Kingdom
Re: cps2 Screen does not appear
I'm not 100% sure that the 245s would be the culprit in that case. When my failed, the fault was the same as kobayuz777's - the game was running fine but there was a solid colour on the screen. Like NoAffinity says, sounds like a cold solder joint on that custom. Nothing wrong with testing the 245s as well though, but sounds like it may not be the culprit.Asure wrote: ↑October 22nd, 2018, 9:00 pm Just piggybacking along for a ride on this thread.
I have a similar issue with a B board, except the sprite layer comes and goes if i move my hand around in this area like a magician.. I was suspecting the big chip near the battery since touching it makes the layer appear (and stay solid), but it randomly comes & goes. I should give those 245's a check up as well right?
- kobayuz777
- Please Continue...
- Posts: 54
- Joined: June 1st, 2018, 3:16 am
- Location: japan
- eBay: koba27300036
Re: cps2 Screen does not appear
NoAffinity wrote: ↑October 22nd, 2018, 11:05 pm Uhh...how many boards you got there? Nice job on the fix!
Asure, if touching the DL-1927 corrects the problem, then it's likely cold solder joints at that chip. Try reflowing that chip first, as that may be all that's needed.
It is like this.
There are about three more junk boards.
to Mr Asure,
Perhaps it is better to upload images and videos as a defect on the screen.
If you get information from a person with similar experience,
That may be a hint of repair.
-
- Posts: 33
- Joined: August 31st, 2011, 1:02 am
- Location:
Re: cps2 Screen does not appear
duuuudekobayuz777 wrote: ↑November 5th, 2018, 2:09 amNoAffinity wrote: ↑October 22nd, 2018, 11:05 pm Uhh...how many boards you got there? Nice job on the fix!
Asure, if touching the DL-1927 corrects the problem, then it's likely cold solder joints at that chip. Try reflowing that chip first, as that may be all that's needed.
It is like this.
There are about three more junk boards.
to Mr Asure,
Perhaps it is better to upload images and videos as a defect on the screen.
If you get information from a person with similar experience,
That may be a hint of repair.
- leonardoliveira
- Please Continue...
- Posts: 692
- Joined: August 30th, 2012, 5:53 am
- Location: Brazil
- Initials: leo
Re: cps2 Screen does not appear
A true CAPCOM fan, I see.