This is my PSU in Sega NAC, does it have enought juice to run mvs 4-slot? or Naomi with Capcom IO?
thanks.
400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
- TMallu
- Posts: 48
- Joined: February 18th, 2013, 6:14 am
- Location: Finland
- yosai
- Windy City
- Posts: 4061
- Joined: August 17th, 2008, 5:00 pm
- Location: London
- eBay: yosai
Re: 400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
It should do. Have you measured the output voltages?
- TMallu
- Posts: 48
- Joined: February 18th, 2013, 6:14 am
- Location: Finland
Re: 400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
Ok, thanks. No I haven't.
- ninn
- TheRedKnight's Lover
- Posts: 934
- Joined: September 5th, 2011, 1:24 pm
- Location: Vienna, Austria, Europe
- eBay: 8bitbitch
Re: 400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
guess you still don't trust your multimeter, am I right?
It is labeled so very nicely. How much juice to you need?
It is labeled so very nicely. How much juice to you need?
-
- Please Continue...
- Posts: 33
- Joined: October 31st, 2012, 4:49 pm
- Location:
Re: 400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
It should handle a MVS 4-Slot without any issues, but unless you are running the Naomi with the separate JVS power supply it is not going to power it up through the Capcom I/O board.
My power supply board blew out and I modded in a standard Happ PS to replace it (without cutting the cabs wiring). It doubled the current on the +5 volt. Here is how I did it : http://forums.arcade-museum.com/showthread.php?t=258326". The modification instructions are at the bottom of the thread.
Brian.
My power supply board blew out and I modded in a standard Happ PS to replace it (without cutting the cabs wiring). It doubled the current on the +5 volt. Here is how I did it : http://forums.arcade-museum.com/showthread.php?t=258326". The modification instructions are at the bottom of the thread.
Brian.
- TMallu
- Posts: 48
- Joined: February 18th, 2013, 6:14 am
- Location: Finland
Re: 400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
Nice work Brian.
Damn.
So you are saying i cant run naomi 1 rom -games with capcom io using this psu?
Damn.
So you are saying i cant run naomi 1 rom -games with capcom io using this psu?
-
- Please Continue...
- Posts: 33
- Joined: October 31st, 2012, 4:49 pm
- Location:
Re: 400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
If you turn the +5V adjustment screw all the way up you might get some life. The adjustment is on the top of the PS in a little hole, right above the wire connectors. Mine wouldn't, but it doesn't hurt to try it.TMallu wrote:Nice work Brian.
Damn.
So you are saying i cant run naomi 1 rom -games with capcom io using this psu?
Just don't be surprised when you only get a black screen. :p
Brian.
- Switchblade
- Please Continue...
- Posts: 37
- Joined: September 16th, 2012, 9:46 am
- Location: Reading, UK
- eBay: Topcat256
- Initials: SPF
Re: 400-5198-01 PSU in NAC, Mvs 4 slot/Naomi?
I have a NAC with the same power supply. My naomi works fine through a capcom I/0 board with carts.
I also have a Net Dimm and had to convert an ATX PC power supply with some JST plugs and that works great to.
Carts only you should be fine
I also have a Net Dimm and had to convert an ATX PC power supply with some JST plugs and that works great to.
Carts only you should be fine
- TMallu
- Posts: 48
- Joined: February 18th, 2013, 6:14 am
- Location: Finland
Re: 400-5198-01 PSU in NAC, CPS3?
Is this PSU sufficient to run CPS-3 with cd-drive?