Arcade Otaku - アーケード オタク

Hi everyone, i have a New Astro City and i tried looking online to find a kick harness for the Namco System 246 but i havent been in luck, could someone kindly tell me where i can purchase one? I tried the below and it was too big https://i.ebayimg.com/images/g/r-UAAOSwl6Rd26Y2/s-l1600.jpg this is h...

Hi everyone I have a Namco 256 and I have no idea how to connect the jamaa kick harness to this adapter for an new ASTRO city,.

I posted a photo below.

Appriciate any help I can get.

Forgot thisb

i think on the pandora its wire video ground to pin 1, your jamma looks wired for video ground on pin 14 who knows what has been done previously on the cab wiring wise a quick way to see if it is related to video ground is just link pin 1 and pin 14 , how you do that is up to you- maybe with a bit ...

grantspain wrote: ↑

December 22nd, 2019, 4:17 pm

looks like video ground is missing, normal jamma on pin 14 and on chinese multigames is on pin 1

so should i replace the whole jamaa cable? im a complete noob sorry :/ can you tell me what i should do

Forgot to add this to,

Would Appriciate any help I can get.

Hi everyone,
I have an ASTRO city cabinet which I hooked up an pandoras box 4s to and I wanted to know is there a way I can the screen so it doesn't look blurry because I can barely see anything without the lights turned on.

IMG_20191221.jpg The arrow points to the "LOW" 15khz setting. The other connector is for "HIGH" 24khz. You have to turn the pot while the monitor is on. When the image on the monitor stops looking like a squiggly mess, you've found the correct spot. It looks like the pot still has factory glue on i...

Make sure your chassis is set to "LOW". Set Atomiswave to 15khz. Adjust the pot circled in the pic below (H.H.15): IMG_20191221.jpg I'm sorry I'm a real noob, the chassis how can I set it to low and the pot you circles how do I adjust it like how is it supposed to look, I'm sorry I'm asking a lot o...

Is atomiswave switchable 15k/31k like the Naomi? I don't think so Yes, it is. The right dip switch controls resolution. IIRC up is 15khz, down 31khz. EDIT: manual confirms this, https://wiki.arcadeotaku.com/images/9/9e/Atomiswave_manual.pdf (page 6) I just tried changing the dip switch same issue. ...

There's some problem with sync. How are you connecting the Naomi to your Blast? It looks like you have an autosyncing MS2931 / 2933 in your Blast, can you confirm? You should have three buttons to control the OSD above the control panel connectors. You could try switching resolution on the Naomi, e...

nem wrote: ↑

December 21st, 2019, 12:59 pm

sds.jpg


You already have a kick harness, you don't need anything else except the buttons.

Thank you very much, i feel really stupid for not noticing

DaveyD wrote: ↑

December 21st, 2019, 12:06 pm

Is atomiswave switchable 15k/31k like the Naomi?

I don't think so, I also just tried a pcb and same issue so i don't think it's the atomiswave.

And thank you everyone for trying to help with this issue.

I hope I can fix this.

PrincessPrinPrin wrote: ↑

December 21st, 2019, 11:44 am

Wires for vertical yoke are in bad condition.

Do you think that's the issue? How can I fix them.

cools wrote: ↑

December 21st, 2019, 11:39 am

Its on 15K. The 4pin connectors are labelled 15K and 24K and are next to each other.

I just switched them and this is what shows up on the screen, the wiggley lines are just different now.

grantspain wrote: ↑

December 21st, 2019, 9:59 am

frequency header on the main chassis
low is 15k
high is 25k

it looks like wrong res or maybe horizontal hold needs a tweek- i think res though

I'm not sure where the frequency is on the main chassis, could you kindly point it out? Thank you

im not sure how do i find out if it is or not? thank you

Hi everyone
I recently got a Blast City i plugged in an Noami board and when i turned it on this is what i got,
[media]https://drive.google.com/file/d/1Nip6HV ... sp=sharing[/media]
I would appreciate it if anyone can help me fix this issue.

Thank you.

Hi everyone i have a new net city but when i purchased it i only got it with 2P 3 Buttons, i wanted to add 3 more buttons to each side but im a noob to this i read that i needed a kick harness and im not really sure where i can add it in the cabinet how? i'm not sure what i can do to fix it and woul...

Hi everyone, i recently got an New Astro City and plugged in an Atomiswave board, i can hear the audio but the video his wiggly lines it looks like something is loose in the video cables, i'm new to cabinets and i'm not sure what i can do to fix it and would appreciate any help i can get.