ms9 no sync

For monitor related issues
Post Reply
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

ms9 no sync

Post by brad808 »

I have an ms9 that got high voltage sent down the ground chain now has no sync. I have no wave on TP1. I've replaced q101 and u101 as per flowchart. Still no pulse. Any suggestions?
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

what is the actual model number of the chassis,is it a standard ms9-29?
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

Hello it is an auto switching ms9a
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

ok so when you say its not sync do you mean its rolling or there is no sync?
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

No sync, just coloured lines. Picture is not rolling though.
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

right so you have lost horizontal hold
does the h.hold pot have any affect on the picture?
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

Yes the hold pot is still working
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

and you have proved signal and wiring?
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

Yes it is being tested on versus city, player 2 monitor is working perfect. Plus I have other ms9 in player 1 side working. All signal is working properly going to monitor.
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

the other chassis are they auto switching as well?
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

I have one auto switching in versus city and 4 other non auto switch.

Originally both auto switch were in versus, originally I unplug player one to test other monitor and fried player 2. Now I have one auto in player one and one manual in player 2 until I fix the auto switch for player 2.
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

ok i was trying to work out if the auto could not detect the sync due to two monitors connected to the same source but obviously it can as it was ok previously

have you swapped out the la7853 yet?
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

No I haven't. That's the next step for me?
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

well i can't see anything else on the sync line that would cause

what exactly happened to cause the fault
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

OK, I'll swap it and report back.

Person gave me monitor to test, I plugged it in player 1 side, it smoked, fried jpac, USB bank, player 2 monitor. There was resistor leg touching ground sent HV down ground line. Was dumb mistake on my part.
User avatar
grantspain
Tech Head
Posts: 4823
Joined: August 17th, 2008, 4:23 pm
Location: down south

Re: ms9 no sync

Post by grantspain »

i had something similar last week but not a ms9
it caused me a lot of problems
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

la7853 has been replaced and still not working. Back to the drawing board
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

Do you have a good copy of a schematic for these? the only ones I find are super blurry
thanks
brad808
Posts: 33
Joined: August 31st, 2011, 1:02 am
Location:

Re: ms9 no sync

Post by brad808 »

Anyone have schematics for these monitors?
Post Reply